DOOSAN DL160
See also:
| Fault Codes ID | Malfunction/Fault Description |
| 12 | Indicates the end of a single pass through the fault list. |
| 14 | Sensor input ECT Low level usually appears if the coolant sensor wire is short on mass. |
| 15 | Sensor input ECT High level if the coolant sensor wire is disconnected or wire breakage. |
| 16 | ECT too high the temperature of the coolant, measures excessive temperature or Shorted Or on the mass sits. |
| 22 | Throttle sensor. Input signal Wire InputLo Tps1 in the cliff |
| 23 | TPS1 Throttle input sensor is short |
| 24 | The sensor of the throttle valve of the TPS. Sensor malfunction |
| 25 | Throttle temperature sensor TPS malfunction sensor |
| 26 | ETC Sensor wire etc in breakage or throttle plate sticks out inside the throttle body |
| 27 | The projected difference of TPS 1 differs from the calculated position |
| 28 | ETC early test worked. Throttle Spring return Error |
| 29 | ETC Driver Fault Current driver throttle or driver signals are short |
| 33 | Sensor low signal MAP wire in breakage or open the chip |
| 34 | High MAP signal short or sensor failure |
| 37 | IAT sensor input Low, TMAP sensor failure or short circuit |
| 38 | IAT sensor input is high, TMAP is off or IAT signal is open |
| 42 | EST 1. Low signal driver coil low or under closed on plus |
| 43 | EST 1. High or high-current excitation signal |
| 52 | Low oil pressure in the engine |
| 53 | Battery charge sensor input, low battery voltage measured below 8.0 in Dc |
| 54 | Battery sensor input high battery voltage, measured above 15.9 in Dc |
| 55 | Sensor input XDRP Low sensor level, lower 4.6 In Dc |
| 56 | Sensor input XDRP High sensor level, higher 5.2 In Dc |
| 57 | The increased speed of the engine has exceeded the given value of maximum speed of rotation |
| 61 | Pedal Sensor Input 1 What The APP1 signal is disconnected, the circuit is open or the sensor malfunctions |
| 62 | Pedal Sensor Input 1 Hi APP1 sensor error or short circuit |
| 63 | Pedal Sensor range 1 What Potentiometer APP1 |
| 64 | Pedal Sensor range 1 Hi Potentiometer APP1 not working |
| 65 | Pedal Sensor input What APP2 or short-circuit sensor error |
| 66 | Pedal Sensor Input 2 Hi APP2 signal off, circuit break or sensor malfunction |
| 67 | Pedal Sensor Range 2 local malfunction of the potentiometer APP2 |
| 68 | Pedal Sensor Range 2 Hi APP2 malfunction of the potentiometer |
| 69 | Pedal 1. Pedal 2. The difference of the measured signal position of the APP2 pedal differs from the APP1 |
| 71 | AFR Trim Valve Output. FTV Modulation driver signal Error |
| 72 | Shut-off valve AFR lower working cycle FTV at lower limit (LEAN) |
| 73 | AFR Trim Valve -Upper working cycle DC FTV at the top (RICH) limit |
| 74 | Switching sensor O2 sensor does not switch through the voltage of the support AFR |
| 77 | Oxygen sensor input High O2 sensor signal is short on + 5 in Dc. |
YTO Tractor owner's, service and maintenance manuals, tech specs, spare parts manuals & catalogs, wiring…
Yishan Bulldozer T160, T180, TS180, TSc180, TY160, TY180 and TY220 owner's, service and maintenance manuals,…
Wolf Garten Lawn Mower owner's, service and maintenance manuals, tech specs, spare parts manuals &…
Vermeer maintenance, service and operator's manuals in PDF for: heavy equipment, skid steer loaders, drill…
Venieri Wheel and Backhoe Loader: owner's, service and maintenance manuals, tech specs, spare parts manuals…
Valpadana Blitz 150, 4RM-180, 4RM-260, 4RM-350, 450, VP4600 and VP 7000-9000, 7060 and 7070 tractors:…