Kalmar DRF 400-450
See also:
Kalmar DRF 400-450
When contacting engine suppliers, use Volvo/Cummins codes.
PID, PPID, SID, PSID / FMI
| FMI | Description | SAE-text |
| 0 | Too high value. | Valid data, but higher than normal operating range. |
| 1 | Too low value. | Valid data, but lower than normal operating range. |
| 2 | Incorrect data. | Intermittent or incorrect data. |
| 3 | Electric problem. | Abnormally high voltage or short-circuiting to higher voltage. |
| 4 | Electric problem. | Abnormally low voltage or short-circuiting to lower voltage. |
| 5 | Electric problem. | Abnormally low current or open circuit. |
| 6 | Electric problem. | Abnormally high current or short-circuiting to frame ground. |
| 7 | Mechanical problem. | Incorrect response from mechanical system. |
| 8 | Mechanical problem or electric problem. | Abnormal frequency. |
| 9 | Communication error. | Abnormal update rate. |
| 10 | Mechanical problem or electric problem. | Abnormally large variations. |
| 11 | Unknown error. | Non-identifiable error. |
| 12 | Component problem. | Defective unit or component. |
| 13 | Incorrect calibration. | Values outside calibration values. |
| 14 | Unknown error. | Special instructions. |
| 15 | Unknown error. | Reserved for future use. |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 94/FMI | 3.6 | PID94/ FMI | Sensor fuel pres- sure short- circuited to volt- age, ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/2:3 Volvo TAD1250VE: D794/B:16 | – |
| 94/FMI | 3.8 | PID94/ FMI | Low fuel pressure (feed). | No limitation. | Change fuel filter. Change fuel prefilter. Check if pressure can be built up with the hand pump. | – | – |
| 97/1 | 2.1 | PID97/ 1 | Water in fuel. | No limitation. | Drain water separator. Clean metal filter in the fuel feed’s hose connection on the engine. Check fuel filter and fuel pre-filter. | – | – |
| 97/3 | 2.9 | PID97/ 3 | Sensor water in fuel short- circuiting to ground or open circuit. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/2:4 Volvo TAD1250VE: D794/B:8 | – |
| 98/FMI | 5.7 | PID98/ FMI | Low oil level. | No limitation. | Check oil level. | – | Engine, menu 6 |
| 98/FMI | 5.9 | PID98/ FMI | Sensor oil level short-circuiting to voltage, ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TAD1250VE: D794/B:3, B:4, A:31 | ENGINE, menu 6 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 100/1 | 6.6 | PID100 /1 | Low engine oil pressure. | Engine is shut off. | Check oil level. Change oil filter. Check the system pressure valves and the safety valve in the lubrication system. Check the sensor. | – | ENGINE, menu 6 |
| 100/3 | 3.1 | PID100 /3 | Sensor oil pressure cable short- circuited to volt- age. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:14 Volvo TAD1250VE: D794/B:11 | ENGINE, menu 6 |
| 100/4 | 3.1 | PID100 /4 | Sensor oil pressure, open circuit, or short-circuiting to ground. | No limitation. | Check cable har- ness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:14 Volvo TAD1250VE: D794/B:11 | ENGINE, menu 6 |
| 102/0 | 3.5 | PID102 /0 | Boost pressure too high. | No limitation. | Check the turbo- charger. Check the sensor. Check fuel quality and injectors. | – | ENGINE, menu 6 |
| 102/1 | 3.5 | PID102 /1 | Boost pressure too low. | Reduced engine power. | Check the air filter. Check the turbo- charger. Check the sensor. Check the fuel feed pressure. | – | ENGINE, menu 6 |
| 102/3 | 3.4 | PID102 /3 | Sensor boost pressure, cable short- circuited to volt- age. | Engine smokes more than normal during acceleration or when load- ed. | Check cable har- ness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:3 Volvo TAD1250VE: D794/A:22 | ENGINE, menu 7 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 102/4 | 3.4 | PID102 /4 | Sensor boost pressure, cable short- circuited to ground or open circuit. | Engine smokes more than normal during acceleration or when load- ed. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:3 Volvo TAD1250VE: D794/A:22 | ENGINE, menu 7 |
| 105/0 | 6.2 | PID105 /0 | High charge-air temperature. | Engine is shut off. | Check coolant level. Check that the charge-air cooler is clean. Check thermostat. Check the sensor. | – | ENGINE, menu 7 |
| 105/3 | 3.2 | PID105 /3 | Sensor charge-air temperature, cable short-circuited to voltage or open circuit. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:2 Volvo TAD1250VE: D794/A:47 | ENGINE, menu 7 |
| 105/4 | 3.3 | PID105 /4 | Sensor charge-air temperature, cable short-circuited to ground or open circuit. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:2 Volvo TAD1250VE: D794/A:47 | ENGINE, menu 7 |
| 106/ FMI | 3.4 | PID106 /FMI | Sensor boost pressure, short- circuiting to volt- age, frame ground, or open circuit. | Engine smokes more than normal during acceleration or when load- ed. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:3 Volvo TAD1250VE: D794/A:22 | ENGINE, menu 6 |
| 106/ FMI | 3.5 | PID106 /FMI | Boost pressure too high. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | – | ENGINE, menu 6 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 110/0 | 6.1 | PID110 /0 | High coolant temperature. | Volvo TWD1240VE: Engine is shut off. Volvo TAD1250VE: No limitation. | Check coolant lev- el. Check that radiator is clean. Check thermostat. Check the cap on the expansion tank. Check if there’s air in coolant system. Check the sensor. | – | ENGINE, menu 7 |
| 110/3 | 3.3 | PID110 /3 | Sensor coolant temperature, cable short-circuited to voltage or open circuit. | Preheating is activated even if engine is warm. | Check cable har- ness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:25 Volvo TAD1250VE: D794/B:27 | ENGINE, menu 7 |
| 110/4 | 3.3 | PID110 /4 | Sensor coolant temperature, cable short-circuited to ground. | Preheating is activated even if engine is warm. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:25 Volvo TAD1250VE: D794/B:27 | ENGINE, menu 7 |
| 111/1 | 2.2 | PID111 /1 | Low coolant level. | Volvo TAD1250VE: Engine is shut off. Volvo TAD1250VE: No limitation. | Check the coolant level, top up if needed. Check the sensor. | – | – |
| 111/ FMI | 2.3 | PID111 /FMI | Sensor coolant level, short- circuited to volt- age. | Volvo TWD1240VE: Engine is shut off. Volvo TAD1250VE: No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/2:7 Volvo TAD1250VE: D794/B:23 | – |
| 153/ FMI | 7.7 | PID153 /FMI | Crankcase ventilation pressure too high. | No limitation. | Clean crankcase ventilation. Check wear of cylinder liner, piston, and piston rings. | – | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 153/ FMI | 7.7 | PID153 /FMI | Sensor crankcase ventilation pressure, short- circuiting to volt- age, frame ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TAD1250VE: D794/B:28 | – |
| 158/ FMI | 3.9 | PID158 /FMI | Low battery volt- age. | Engine may be difficult to start. | Check and charge the batteries. Check the alternator. Check the battery cables. | – | – |
| 172/ FMI | 7.9 | PID172 /FMI | Sensor air temperature inlet, short- circuited to voltage, ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:2 Volvo TAD1250VE: D794/A:47 | ENGINE, menu 7 |
| 175/0 | 5.8 | PID175 /0 | High engine oil temperature. | Reduced engine power. | Check oil level. Check the lubrication system’s thermostat. Check the sensor. | – | ENGINE, menu 7 |
| 175/3 | 3.7 | PID175 /3 | Sensor oil temperature, cable short- circuited to voltage or open circuit. | No limitation. | Check cable har- ness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:1 Volvo TAD1250VE: D794/A:31, B:3, B:4 | ENGINE, menu 7 |
| 175/4 | 3.7 | PID175 /4 | Sensor oil temperature, cable short- circuited to ground. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:1 Volvo TAD1250VE: D794/A:31, B:3, B:4 | ENGINE, menu 7 |
| 190/ FMI | 2.6 | PID190 /FMI | Engine rpm too high. | No limitation. | Ease off throttle or select higher gear. | – | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 608/ FMI | – | PPID9 8/FMI | Signal error for start and stop. | No limitation. | Check CAN-bus drivetrain. | – | CAN/ POWER, menu 3 |
| 620/3 1079/2 | 9.3 | SID232 /3 | Voltage feed to sensors, cable short-circuited to voltage. | Several error codes for defective sensor. Reduced engine power. Incorrect instrument values. | Check cable harness between the control unit and the component. | Volvo TWD1240VE: D794/1:5 Volvo TAD1250VE: D794/B:17 | – |
| 620/4 1079/3 | 9.3 | SID232 /4 | Voltage feed to sensors, cable short-circuited to ground. | Several error codes for defective sensor. Reduced engine power. Incorrect instrument values. | Check cable harness between the control unit and the component. | Volvo TWD1240VE: D794/1:4 Volvo TAD1250VE. D794/B:17 | – |
| 626/3 | 5.4 | PID45/ 3 | Preheating relay, cable short- circuited to volt- age. | Preheating can- not be activated. | Check cable harness between the control unit and the component. Check the relay. | Volvo TWD1240VE: D794/2:36 Volvo TAD1250VE: D794/B:25 | ENGINE, menu 5 |
| 626/4 | 5.4 | PID45/ 4 | Preheating relay, cable short- circuited to ground. | Preheating is al- ways activated. | Check cable harness between the control unit and the component. Check the relay. | Volvo TWD1240VE: D794/2:36 Volvo TAD1250VE: D794/B:25 | ENGINE, menu 5 |
| 626/5 | 5.4 | PID45/ 5 | Preheating relay open circuit on cable or defective component. | Preheating can- not be activated. | Check cable harness between the control unit and the component. Check the relay. | Volvo TWD1240VE: D794/2:36 Volvo TAD1250VE: D794/B:25 | ENGINE, menu 5 |
| 629/ FMI | 9.9 | SID254 /FMI | Control unit engine (D794) internal error. | Engine doesn’t start. Engine runs rough. | Change the control unit. | – | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 630/ FMI | 9.9 | SID253 /FMI | Control unit engine (D794) memory error. | Engine doesn’t start. | Re-program the control unit. | – | – |
| 636/3 | 2.5 | SID21/3 | Sensor rpm camshaft, no signal. | Engine takes longer time to start than normal. Engine runs normally when it has started. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:7, 1:18 Volvo TAD1250VE: D794/B:45, B:46 | – |
| 636/8 | 2.5 | SID21/8 | Sensor engine rpm, camshaft, abnormal frequency. | Engine takes longer time to start than normal. Engine runs normally when it has started. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:7, 1:18 Volvo TAD1250VE: D794/B:45, B:46 | – |
| 637/2 | 2.4 | SID22/2 | Sensor engine rpm, flywheel, irregular signal. | Engine is extremely difficult to start and runs rough, if it starts. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 | ENGINE, menu 2 |
| 637/3 | 2.4 | SID22/3 | Sensor engine rpm, flywheel, abnormal frequency. | Engine is extremely difficult to start and runs rough, if it starts. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 | ENGINE, menu 2 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 630/ FMI | 9.9 | SID253 /FMI | Control unit engine (D794) memory error. | Engine doesn’t start. | Re-program the control unit. | – | – |
| 636/3 | 2.5 | SID21/3 | Sensor rpm camshaft, no signal. | Engine takes longer time to start than normal. Engine runs normally when it has started. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:7, 1:18 Volvo TAD1250VE: D794/B:45, B:46 | – |
| 636/8 | 2.5 | SID21/8 | Sensor engine rpm, camshaft, abnormal frequency. | Engine takes longer time to start than normal. Engine runs normally when it has started. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:7, 1:18 Volvo TAD1250VE: D794/B:45, B:46 | – |
| 637/2 | 2.4 | SID22/2 | Sensor engine rpm, flywheel, irregular signal. | Engine is extremely difficult to start and runs rough, if it starts. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 | ENGINE, menu 2 |
| 637/3 | 2.4 | SID22/3 | Sensor engine rpm, flywheel, abnormal frequency. | Engine is extremely difficult to start and runs rough, if it starts. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 | ENGINE, menu 2 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 637/8 | 2.4 | SID22/ 8 | Sensor engine rpm, flywheel, abnormal frequency. | Engine is extremely difficult to start and runs rough, if it starts. | Check cable harness between the control unit and the component. Check that the sensor is correctly connected. | Volvo TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 | ENGINE, menu 2 |
| 639/FMI 2017/FMI | 6.5 | SID231/FMI PSID201/FMI | Communication error with Engine control unit (D794), configuration error. | Engine off: engine cannot be started. Engine on: engine goes to idle and can only be stopped by using the emergency stop. | Use diagnostic menu to find incorrect segment. Check cable harness between the control unit and the component. Check the control unit. | Volvo TWD1240VE: D794/2:1, 2:2 Volvo TAD1250VE: D794/B:51, B:55 | CAN/ POWER, menu 3 |
| 639/FMI | 6.4 | SID231 /FMI | Communication error with Engine control unit (D794), configuration error. | Instruments and controls do not work. | Use diagnostic menu to find incorrect segment. Check cable har- ness between the control unit and the component. Check the control unit. | – | CAN/ POWER, menu 3 |
| 639/FMI | 9.9 | SID240 /FMI | Memory error engine control unit. | It may not be possible to start the engine. | Re-program the control unit. | – | – |
| 651/2 | 7.1 | SID1/2 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 651/3 | 7.1 | SID1/3 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 | – |
| 651/4 | 7.1 | SID1/4 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 | – |
| 651/5 | 7.1 | SID1/5 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 | – |
| 651/7 | 7.1 | SID1/7 | Incorrect compression or defective injector cylinder 1. | Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance. Check cable harness between the control unit and the component. Check the injector. Perform compression test and check cylinder 1. | Volvo TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 | – |
| Description | Limitation | Action | Connection and compo- nent | Diag- nostic menu | |||
| Code | Flash | J1587 | |||||
| 651/11 | 7.1 | SID1/11 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 | – |
| 652/2 | 7.2 | SID2/2 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:20, A:24 | – |
| 652/3 | 7.2 | SID2/3 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 | – |
| 652/4 | 7.2 | SID2/4 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 | – |
| 652/5 | 7.2 | SID2/5 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 652/7 | 7.2 | SID2/7 | Incorrect compression or defective injector cylinder 2. | Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance. Check cable harness between the control unit and the component. Check the injector. Perform compression test and check cylinder 2. | Volvo TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 | – |
| 652/11 | 123DTC7.2 | SID2/ 11 | Electric failure, injector cylinder 2. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 | – |
| 653/2 | 7.3 | SID3/2 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 | – |
| 653/3 | 7.3 | SID3/3 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE. D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 653/4 | 7.3 | SID3/4 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 | – |
| 653/5 | 7.3 | SID3/5 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 | – |
| 653/7 | 7.3 | SID3/7 | Incorrect compression or defective injector cylinder 3. | Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance. Check cable harness between the control unit and the component. Check the injector. Perform compression test and check cylinder 3. | Volvo TWD1240VE: D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 | – |
| 653/11 | 7.3 | SID3/11 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 654/2 | 140 DTC 7.4 | SID4/2 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 | – |
| 654/3 | 7.4 | SID4/3 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 | – |
| 654/4 | 7.4 | SID4/4 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 | – |
| 654/5 | 7.4 | SID4/5 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 654/7 | 7.4 | SID4/7 | Incorrect compression or defective injector cylinder 4. | Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance. Check cable harness between the control unit and the component. Check the injector. Perform compression test and check cylinder 4. | Volvo TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 | – |
| 654/11 | 7.4 | SID4/ 11 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 | – |
| 655/2 | 7.5 | SID5/2 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 | – |
| 655/3 | 7.5 | SID5/3 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 655/4 | 7.5 | SID5/4 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 | – |
| 655/5 | 7.5 | SID5/5 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 | – |
| 655/7 | 7.5 | SID5/7 | Incorrect compression or defective injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check that cabling to the injectors is not damaged. Check cable harness between the control unit and the component. Check the injector. Perform compression test and check cylinder 5. | Volvo TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 | – |
| 655/11 | 7.5 | SID5/ 11 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 656/2 | 7.6 | SID6/2 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the component. | Volvo TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 | – |
| 656/3 | 7.6 | SID6/3 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 | – |
| 656/4 | 7.6 | SID6/4 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 | – |
| 656/5 | 7.6 | SID6/5 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 656/7 | 7.6 | SID6/7 | Incorrect compression or defective injector cylinder 6. | Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance. Check cable harness between the control unit and the component. Check the injector. Perform compression test and check cylinder 6. | Volvo TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 | – |
| 656/11 | 7.6 | SID6/ 11 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VED 794/A:36, A:40 | – |
| 677/ FMI | 6.3 | PPID3/ FMI SID39/ FMI | Starter motor re-lay, short-circuiting to voltage ground. | Engine doesn’t start. Engine starts immediately when ignition is turned on. | Check cable harness between the control unit and the component. Check the motor. | Volvo TWD1240VE: D794/2:31 Volvo TAD1250VED 794/B:29 | ENGINE, menu 5 |
| 1485/3 | 5.1 | PPID5/ 3 | Main relay, cable short-circuited to voltage. | Instrument panel loses voltage when ignition key is turned to start position. Engine doesn’t start. | Check cable harness between the control unit and the component. Check the relay. | Volvo TWD1240VE: D794/1:32 Volvo TAD1250VE: D794/A:8 | – |
| 2791/ FMI | – | PPID1 9/FMI | Internal EGR, electric problem or mechanical problem. | No limitation. | Check sensor boost pressure. Check the component. (IEGR) Contact Volvo Penta workshop for more information. | Volvo TAD1250VE: D794/B:30 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 52019 2/FMI | 6.8 | PPID8/ FMI | Sensor piston cooling pressure short-circuiting to voltage, ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | Volvo TAD1250VE: D794/B:14 | – |
| 52019 2/FMI | 6.7 | PPID8/ FMI | Low piston cooling pressure. | No limitation. | Check that engine’s oil pressure is higher than 175 kPa. | – | – |
| 52019 5/FMI | 4.8 | PPID4/ FMI | Stop input on control unit short-circuits to ground or open circuit. | Engine cannot be shut off. | Check cable harness between the control unit and the component. | Volvo TWD1240VE: D794/2:6 Volvo TAD1250VE: D794/B:27 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 84/2 | 241 | PID08 4/2 | Electric problem sensor speed, data invalid. | Engine rpm restricted to max. rpm without gear. | Check cable harness between the control unit and the component. Check the sensor. | – | – |
| 84/10 | 242 | PID08 4/10 | Electric problem sensor speed, manipulation of signal detected. | Engine rpm restricted to max. rpm without gear. | Check cable harness between the control unit and the component. Check the sensor. | – | – |
| 91/3 | 131 | PID09 1/3 | Electric problem throttle pedal, cable short-circuited to voltage. | Engine does not respond to throttle. | Check cable harness between the control unit and the component. Check the component. | – | – |
| 91/4 | 132 | PID09 1/4 | Electric problem throttle pedal, cable short-circuited to ground. | Engine does not respond to throttle. | Check cable harness between the control unit and the component. Check the component. | – | – |
| 91/8 | 147 | PID09 1/8 | Electric problem throttle pedal, frequency too low. | Engine does not respond to throttle. | Check cable harness between the control unit and the component. Check the component. | – | – |
| 91/8 | 148 | PID09 1/8 | Electric problem throttle pedal, frequency too high. | Engine does not respond to throttle. | Check cable harness between the control unit and the component. Check the component. | – | – |
| 91/19 | 287 | SID09 1/2 | Communication error with Cab control unit (D790-1), electric problem throttle pedal. | Engine only runs on idle. | Use diagnostic menu to localize incorrect segment. | – | CAN/ POWER, menu 3 |
| 97/3 | 428 | PID09 7/3 | Electric problem sensor water in fuel, cable short- circuited to voltage. | No limitation. | Check cable harness between the control unit and the component. Check the component. | D794/Sen- sor:09 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 97/4 | 429 | PID09 7/4 | Electric problem sensor water in fuel, cable short- circuited to ground. | No limitation. | Check cable harness between the control unit and the component. Check the component. | D794/Sen- sor:09 | – |
| 97/15 | 418 | PID09 7/15 | Water in fuel. | Risk of white exhaust smoke and reduced engine power. | Drain water from the fuel filter. | – | – |
| 100/1 | 415 | PID10 0/1 | Low engine oil pressure. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check oil level in the engine, top up as need- ed. | – | ENGINE, menu 6 |
| 100/2 | 435 | PID10 0/2 | Sensor oil pressure, data error. | No warning for low oil pressure engine. | Check the sensor. | D794/Sen- sor:44 | ENGINE, menu 6 |
| 100/3 | 135 | PID10 0/3 | Sensor oil pressure cable short- circuited to voltage. | No warning for low oil pressure engine. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sen- sor:44 | ENGINE, menu 6 |
| 100/4 | 141 | PID10 0/4 | Sensor oil pressure, open circuit, or short-circuiting to ground. | No warning for low oil pressure engine. | Check cable harness between the control unit and the component. Check the sensor. | D794/ Black:14 | ENGINE, menu 6 |
| 100/ 18 | 143 | PID10 0/1 | Low engine oil pressure. | No limitation. | Check oil level in the engine, top up as need- ed. Check the sensor. | – | ENGINE, menu 6 |
| 102/2 | 433 | PID10 2/2 | Sensor boost pressure indicates high boost pressure, but other engine data indicate that pressure should be nor- mal. | Reduced engine power. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sen- sor:39 | ENGINE, menu 7 |
| 102/3 | 122 | PID10 2/3 | Sensor boost pressure, cable short- circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sen- sor:39 | ENGINE, menu 7 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 102/4 | 123 | PID10 2/4 | Sensor boost pressure, cable short- circuited to ground or open circuit. | Reduced engine power. | Check cabling between control unit and component. Check sensor boost pressure. | D794/ Black:3 | ENGINE, menu 7 |
| 103/ 16 | 595 | PID10 3/0 | Overspeed protection turbo. | Reduced engine power. | Check the component. | – | – |
| 105/0 | 155 | PID10 5/0 | Inlet air too warm. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check the coolant level in the engine, top up as needed. Check that the charge- air cooler is clean, clean as needed. Check that the fan belts are intact. Check sensor inlet air temperature. | – | ENGINE, menu 7 |
| 105/3 | 153 | PID10 5/3 | Sensor charge-air temperature, cable short-circuited to voltage or open circuit. | Risk of white exhaust smoke. No warning for high coolant temperature. | Check cabling between control unit and component. Check that sensor charge-air temperature is installed correctly and connected. Check sensor charge- air temperature. | D794/Sen- sor:38 | ENGINE, menu 7 |
| 105/4 | 154 | PID10 5/4 | Sensor charge-air temperature, cable short-circuited to ground or open circuit. | Risk of white exhaust smoke. No warning for high coolant temperature. | Check cable harness between the control unit and the component. Check that sensor is in- stalled correctly and connected. Check the sensor. | D794/Sen- sor:38 | ENGINE, menu 7 |
| 108/2 | 295 | PID10 8/2 | Electric problem sensor air pressure, data error. | Reduced engine power. | Check the sensor. | – | – |
| 108/3 | 221 | PID10 8/3 | Electric problem air pressure, cable short-circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sensor:06 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 108/4 | 222 | PID10 8/4 | Electric problem air pressure, cable short-circuited to ground. | Reduced engine power. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sen- sor:06 | – |
| 110/0 | 151 | PID11 0/0 | High coolant temperature. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check coolant level. Check that radiator is clean. Check if there’s air in coolant system. Check the cap on the expansion tank. Check the sensor. Check thermostat. | – | ENGINE, menu 7 |
| 110/3 | 144 | PID11 0/3 | Sensor coolant temperature, cable short-circuited to voltage or open circuit. | No display of engine temperature. | Check cable harness between the control unit and the component. | D794/Sen- sor:02 | ENGINE, menu 7 |
| 110/4 | 145 | PID11 0/4 | Sensor coolant temperature, cable short-circuited to ground. | No display of engine temperature. | Check cable harness between the control unit and the component. Check that the sensor is correctly connected. Check the sensor. | D794/Sen- sor:02 | ENGINE, menu 7 |
| 111/1 | 235 | PID11 1/1 | Low coolant level. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check the coolant level, top up if needed. Check the sensor. | – | – |
| 111/2 | 422 | PID11 1/2 | Electric problem sensor coolant lev- el, data error. | No warning for low coolant level. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sen- sor:09 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 166/2 | 951 | PID11 6/2 | Power imbalance between cylinders. | Rough idling. | Check the fuel quality. If the fuel system has been opened so that air may have entered the system, the error code may be generated. Troubleshoot the engine. | – | – |
| 167/1 | 598 | PID16 7/1 | Low battery volt- age. | Warning active until voltage is correct. | Check batteries and alternator. | D794/ OEM:7, 8, 17, 18, 28 | – |
| 167/ 16 | 596 | PID16 7/0 | Low battery volt- age. | Warning active until voltage is correct. | Check fuses. Check batteries and alternator. | D794/ OEM:7, 8, 17, 18, 28 | – |
| 167/ 18 | 597 | PID16 7/1 | High battery volt- age. | Warning active until voltage is correct, engine runs at high idle to increase volt- age. | Check batteries and alternator. | D794/ OEM:7, 8, 17, 18, 28 | – |
| 168/ 16 | 442 | PID16 8/0 | Voltage feed to control unit high. | No limitation. | Check fuses. Check batteries and alternator. | D794/ OEM:7, 8, 17, 18, 28 | – |
| 168/ 18 | 441 | PID16 8/1 | Voltage feed to control unit low. | Rough idling. | Check fuses. Check batteries and alternator. | D794/ OEM:7, 8, 17, 18, 28 | – |
| 175/0 | 214 | PID17 5/0 | High engine oil temperature. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check coolant level and oil level in engine, top up as needed. Check that the oil cooler is clean, clean as need- ed. Check that the fan belts are intact. Check the sensor. | – | ENGINE, menu 7 |
| 175/3 | 212 | PID17 5/3 | Sensor oil temperature, cable short- circuited to voltage or open circuit. | No display of oil temperature engine. | Check cable harness between the control unit and the component. Check that the sensor is correctly connected. | D794/Sen- sor:42 | ENGINE, menu 7 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 175/4 | 213 | PID17 5/4 | Sensor oil temperature, cable short- circuited to ground. | No display of oil temperature engine. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sen- sor:42 | ENGINE, menu 7 |
| 188/4 | 466 | SID03 2/4 | Electric problem solenoid valve wastegate 1 short- circuiting to ground. | Reduced engine power. | Check cable harness between the control unit and the component. Check the solenoid valve. | D794/Actuator: 24 | |
| 190/0 | 234 | PID19 0/0 | Engine rpm too high. | Fuel feed is restricted until engine rpm is below permitted rpm. | Ease off throttle or select higher gear. | – | – |
| 190/2 | 115 | PID19 0/2 | Electric problem sensor rpm/ignition position, no signal from any of the sensors. | Engine stops and cannot be started. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sen- sor:47, 50 | – |
| 190/ 10 | 121 | PID19 0/10 | Electric problem sensor rpm/ignition position, on of two signals is missing. | No limitation. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sensor: 47, 50 | – |
| 191/ 16 | 349 | PID19 1/0 | Speed limitation activated. | Speed is reduced. | Ease off throttle. | – | – |
| 191/ 18 | 489 | PID19 1/1 | Speed warning for low speed. | Engine only runs on idle. | Increase throttle. | – | – |
| 251/2 | 319 | PID25 1/2 | Internal error Control unit engine. | – | – | – | – |
| 441/3 | 293 | PID44 1/3 | Extra sensor temperature short- circuited to ground. | No warning at high temperature Control unit engine (D794). | Check cable harness between the control unit and the component. Check the sensor. | D794/Sensor: 12 | |
| 441/4 | 294 | PID44 1/4 | Extra sensor temperature short- circuited to voltage. | No warning at high temperature Control unit engine (D794). | Check cable harness between the control unit and the component. Check the sensor. | D794/Sensor: 12 | |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 558/2 | 431 | SID23 0/2 | Electric problem sensor throttle ped- al, idle switch data error. | No limitation. | Check cable between control unit and component. Check component. | D794/ OEM: 03, 13 | – |
| 558/4 | 551 | SID23 0/4 | Electric problem sensor throttle ped- al, idle switch cable short-circuited to ground. | Engine does not respond to throttle. | Check cable between control unit and compo- nent. Check component. | D794/ OEM: 03, 13 | – |
| 558/ 13 | 432 | SID23 0/13 | Electric problem sensor throttle ped- al, idle switch calibration error. | Engine only runs on idle. | Check cable between control unit and component. Check component. | D794/ OEM: 13 | – |
| 608/2 | 412 | SID25 0/2 | Communication error with Control unit engine (D794). | No limitation. | Check the control unit. | D794/ OEM: 26, 27, 36, 37, 46 | |
| 608/9 | 414 | SID25 0/9 | Communication error with Control unit engine (D794). | No limitation. | Check the control unit. | D794/ OEM: 26, 27, 36, 37, 46 | |
| 620/3 1080/ 3 | 227 | SID23 2/3 | Electric problem reference voltage to sensor short- circuited to voltage. | Reduced engine power. No warning low oil pressure or low coolant level. | Check cable harness between the control unit and the component. Check the control unit. | D794/Sensor: 18, 25, 45 | – |
| 620/4 1081/ 4 | 187 | SID23 2/4 | Electric problem reference voltage to sensor short- circuited to ground. | Reduced engine power. No warning low oil pressure or low coolant level. | Check cable harness between the control unit and the component. Check the component. | D794/Sensor: 18, 25, 45 | – |
| 626/ 11 | 381 | SID23 7/11 | Electric problem to control of relay pre- heating. | Preheating does not work. Risk of white smoke | Check cable harness between the control unit and the component. Check the component. | D794/Actuator: 34 | ENGINE, menu 5 |
| 627/2 | 434 | SID25 1/2 | Voltage feed to control unit disappears without engine off. | Reduced engine power. Engine difficult to start or engine stops. | Check fuses. Check batteries and alternator. | D794/ OEM:7, 8, 17, 18, 28 | – |
| 629/ 12 | 111 | SID25 4/12 | Internal error Control unit engine. | Engine doesn’t start. | Check the control unit. | – | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 629/ 12 | 343 | SID25 4/12 | Internal error Control unit engine. | No limitation. | Check the control unit. | – | – |
| 630/2 | 341 | SID25 3/2 | Software error control unit, engine (D794). | Reduced engine power. Engine difficult to start or engine stops. | Re-program the soft- ware in Control unit engine (D794). | – | – |
| 632/3 | 255 | SID01 7/3 | Electric problem solenoid valve fuel shut-off, cable short-circuited to voltage. | No limitation. | Check cable harness between the control unit and the component. Check the solenoid valve. | D794/Actuator: 33 | – |
| 632/4 | 254 | SID01 7/4 | Electric problem solenoid valve fuel shut-off, cable short-circuited to ground. | Engine is shut off. | Check cable harness between the control unit and the component. Check the solenoid valve. | D794/Actuator: 33 | – |
| 639/2 | 426 | SID23 1/2 | Communication error with Control unit engine (D794). | Functions via CAN-bus do not work. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER, menu 2 |
| 639/9 | 427 | SID23 1/9 | Communication error with Control unit engine (D794). | Functions via CAN-bus do not work. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER, menu 2 |
| 639/9 | 285 | SID23 1/9 | Communication error with Engine control unit (D794), timeout error. | Functions via CAN-bus do not work. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER, menu 2 |
| 639/ 13 | 286 | SID23 1/13 | Communication error with Engine control unit (D794), configuration error. | Functions via CAN-bus do not work. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER, menu 2 |
| 644/2 | 237 | SID03 0/2 | Electric problem throttle pedal, signal outside valid range. | Engine is shut off. | Check cable harness between the control unit and the component. Check the component. | – | – |
| 647/4 | 245 | SID03 3/4 | Electric problem fan connection, cable short-circuited to ground. | Cooling fan al- ways driven. | Check cable harness between the control unit and the component. Check the component. | D794/Ac- tuator:10, Actuator: 9 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 651/5 | 322 | SID00 1/5 | Electric problem injector cylinder 1, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator:10, Actuator: 9 | – |
| 651/6 | 311 | SID00 1/7 | Electric problem injector cylinder 1, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator:10, Actuator: 9 | – |
| 652/5 | 331 | SID00 2/5 | Electric problem injector cylinder 2, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator: 7, 8 | – |
| 652/6 | 315 | SID00 2/6 | Electric problem injector cylinder 2, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator:7, 8 | – |
| 653/5 | 324 | SID00 3/5 | Electric problem injector cylinder 3, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator:6, 16 | – |
| 653/6 | 313 | SID00 3/6 | Electric problem injector cylinder 3, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable between control unit and component. Check component. | D794/Actuator:6, 16 | – |
| 654/5 | 332 | SID00 4/5 | Electric problem injector cylinder 4, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator:26, 36 | – |
| 654/6 | 321 | SID00 4/6 | Electric problem injector cylinder 4, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator:26, 36 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 655/5 | 323 | SID00 5/5 | Electric problem injector cylinder 5, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator: 3, 4 | – |
| 655/6 | 312 | SID00 5/6 | Electric problem injector cylinder 5, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable between control unit and component. Check component. | D794/Actuator: 3, 4 | – |
| 656/5 | 325 | SID00 6/5 | Electric problem injector cylinder 6, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable between control unit and component. Check component. | D794/Actuator: 1, 2 | – |
| 656/6 | 314 | SID00 6/6 | Electric problem injector cylinder 6, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | D794/Actuator: 1, 2 | – |
| 702/3 | 527 | SID04 0/3 PID15 4/3 | Electric problem extra output 2, cable short-circuited to voltage | No limitation. | Check cable harness between the control unit and the component. Check the component. | D794/Actuator: 14 | – |
| 703/3 | 529 | SID05 1/3 | Electric problem extra output 2, cable short-circuited to voltage | No limitation. | Check cable harness between the control unit and the component. Check the component. | D794/Actuator: 45 | – |
| 974/3 | 133 | SID02 9/3 | Electric problem extra throttle pedal, cable short- circuited to voltage. | Engine does not respond to throttle. | Check cable harness between the control unit and the component. Check the component. | D794/ OEM: 21 | – |
| 974/4 | 134 | SID02 9/4 | Electric problem extra throttle pedal, cable short- circuited to ground. | Engine does not respond to throttle. | Check cable harness between the control unit and the component. Check the component. | D794/ OEM: 21 | – |
| 974/ 19 | 288 | SID02 9/2 | Communication error with Cab control unit (D790-1), electric problem throttle pedal. | Engine does not respond to throttle. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER, menu 2 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 1043/ 3 | 387 | PID22 1/3 | Electric problem throttle pedal reference voltage, cable short-circuited to voltage. | Engine only runs on idle. | Check cable harness between the control unit and the component. Check the component. | D794/ OEM: 48 | – |
| 1043/ 4 | 443 | PID22 1/4 | Electric problem throttle pedal reference voltage, cable short-circuited to ground. | Engine only runs on idle. | Check cable harness between the control unit and the component. Check the component. | D794/ OEM: 48 | – |
| 1072/ 11 | 388 | SID07 0/11 | Electric problem solenoid valve engine brake 2. | Engine brake 1 cannot be activated. | Check cable harness between the control unit and the component. Check the solenoid valve. | D794/Actuator: 44 | – |
| 1073/ 11 | 392 | SID02 9/11 | Electric problem solenoid valve engine brake 2. | Engine brake 2 cannot be activated. | Check cable harness between the control unit and the component. Check the solenoid valve. | D794/Actuator: 44 | – |
| 1079/ 3 | 386 | SID23 2/3 | Electric problem reference voltage to sensor short- circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sesor: 17, 37 | – |
| 1079/ 4 | 352 | SID23 2/4 | Electric problem reference voltage to sensor short- circuited to ground. | Reduced engine power. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sen- sor: 17, 37 | – |
| 1188/ 3 | 465 | SID03 2/3 | Electric problem solenoid valve wastegate 1 short- circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component. Check the solenoid valve. | D794/Actuator: 24 | – |
| 1189/ 3 | 491 | SID08 8/3 | Electric problem solenoid valve wastegate 2 short- circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component. Check the solenoid valve. | D794/Actuator: 23 | |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 1189/ 4 | 492 | SID88/ 4 | Electric problem solenoid valve wastegate 2 short- circuited to ground. | Reduced engine power. | Check cable harness between the control unit and the component. Check the solenoid valve. | D794/Actuator: 23 | |
| 1265/ 4 | 223 | SID08 5/4 | Electric problem solenoid valve oil- burn, cable short- circuited to ground. | No limitation. | Check cable harness between the control unit and the component. Check the solenoid valve. | – | – |
| 1319/ 2 | 419 | PID10 2/2 | Electric problem sensor boost pressure. | Reduced engine power. | Check cable harness between the control unit and the component. Check the sensor. | D794/Sensor: 9 | – |
| 1380/ 1 | 219 | PID01 7/1 | Low oil level engine. | No limitation. | Check oil level in the engine, top up as need- ed. | – | – |
| 1383/ 31 | 611 | SID15 1/11 | Engine shut off in another way than with start key means loading. | No limitation. | Shut off the engine with the start key. | – | – |
| 1384/ 31 | 299 | SID02 9/14 | Engine shut off in another way than with start key means loading. | No limitation. | Shut off the engine with the start key. | – | – |
| 1387/ 3 | 297 | PID22 3/3 | Electric problem extra sensor pressure, cable short- circuited to voltage. | No protection for pressure (customer-specific option). | Check cable harness between the control unit and the component. Check the sensor. | D794/Sesor: 19 | – |
| 1387/ 4 | 298 | PID22 3/4 | Electric problem extra sensor pressure, cable short- circuited to ground. | No protection for pressure (customer-specific option). | Check cable harness between the control unit and the component. Check the sensor. | D794/Sesor: 19 | – |
| 1484/ 31 | 211 | SID21 6/11 | Error codes in other control units. | No limitation. | Check error codes for the other control units on the machine, primarily Control unit cab (D790-1) and Control unit transmission (D793). | – | – |
YTO Tractor owner's, service and maintenance manuals, tech specs, spare parts manuals & catalogs, wiring…
Yishan Bulldozer T160, T180, TS180, TSc180, TY160, TY180 and TY220 owner's, service and maintenance manuals,…
Wolf Garten Lawn Mower owner's, service and maintenance manuals, tech specs, spare parts manuals &…
Vermeer maintenance, service and operator's manuals in PDF for: heavy equipment, skid steer loaders, drill…
Venieri Wheel and Backhoe Loader: owner's, service and maintenance manuals, tech specs, spare parts manuals…
Valpadana Blitz 150, 4RM-180, 4RM-260, 4RM-350, 450, VP4600 and VP 7000-9000, 7060 and 7070 tractors:…