See also:
Parameter:
Additional accelerator
Fault:
FMI 3 The signal voltage of the sensor of the additional accelerator is higher than 4.3 V. Breaking the wire of the connection to the mass point, shorting the signal wire to a wire with a higher voltage, the sensor or the idle switch of the additional accelerator is faulty.
FMI 4 The signal voltage of the sensor additional accelerator below 0.4 V. Breakage of the supply or signal wire. Faulty sensor. Oxidized or damaged contacts in the connectors.
Parameter:
The switch idling number 1
Fault:
FMI 7 The idle switch signal is absent from 0 to 13 percent. Break signal or power wires. Shorting the signal wire to power or ground. Faulty idle switch for additional accelerator. Damaged or oxidized pins in connectors.
Parameter:
SAE J1939 data feed
Fault:
FMI 2 The BBM cannot communicate with other control units over the channel given by SAE J1939. Broken wire data channel between the BBM unit and other control units, the closure of the data channel wires to ground or power. The BBM unit may be faulty.
Parameter:
Program memory
Fault:
FMI 2 Software failure or faulty memory chip in the BBM unit. Reprogram the BBM unit, if the fault persists, replace the BBM unit.
Parameter:
SAE J1708 data feed
Fault:
FMI 2 The BBM block receives incorrect messages through the SAE J1708 data channel. Partial damage to data wiring.
Parameter:
Gauge EEPROM Memory
Fault:
FMI 2 A programming error or malfunctioning memory chip in the BBM unit. Reprogram the BBM unit, if the fault persists, replace the BBM block.
FMI 14 Error in saved data. Incorrect software or defective BBM memory chip. Reprogram the BBM unit, if the fault persists, replace the BBM block.
Parameter:
Relay 1 output signal
Fault:
FMI 3 A short to battery power or a higher voltage between the BBM unit and the relay.
FMI 4 Short to ground between the BBM unit and the relay.
Parameter:
Relay 2 output signal
Fault:
FMI 3 A short to battery power or a higher voltage between the BBM unit and the relay.
FMI 4 Short to ground between the BBM unit and the relay.
Parameter:
Power take-off No. 2 (IOM)
Fault:
FMI 2 The BBM unit activated the MOM, and the return signal is not active or the BBM unit has turned off the MOM, and the return signal is active. Closing the return signal wire from the PTO to a higher voltage or ground. Possible faulty IOM.
FMI 3 A short to battery power or a higher voltage between the BBM unit and the MOM, the relay is faulty, or the MOM is faulty.
FMI 4 A short to ground between the BBM and the PTO unit.
Parameter:
Power take-off No. 3 (IOM)
Fault:
FMI 2 The BBM unit activated the MOM, and the return signal is not active or the BBM unit has turned off the MOM, and the return signal is active. Closing the return signal wire from the PTO to a higher voltage or ground. Possible faulty IOM.
FMI 3 A short to battery power or a higher voltage between the BBM unit and the MOM, the relay is faulty, or the MOM is faulty.
FMI 4 Short to ground between the BBM and the PTO unit.
Parameter:
Activate external trigger signal
Fault:
FMI 3 A short to battery power or a higher voltage between the BBM unit and the component.
FMI 4 Short to ground between the BBM unit and the component.
Parameter:
Engine Trouble Warning
Fault:
FMI 3 A short to battery power or a higher voltage between the BBM unit and the component.
FMI 4 Short to ground between the BBM unit and the component.
Parameter:
PWM input
Fault:
FMI 2 The input signal on the BBB6 pin of the BBM unit is outside the range between 5 and 95% or the interpretation of the PWM signal is impossible. The component is not connected to the BBB6 contact of the BBM unit, Short to power supply or to ground on the BBB6 contact of the BBM block. Break in wiring between the BBM unit and the bodywork component.
FMI 8 The body equipment component is not connected to the BBB6 contact of the BBM unit or a break in the wiring between the BBM unit and the body equipment component.
Parameter:
Communication failure by SAE J1939 data link with MID128 engine control unit
Fault:
FMI 9 The BBM MID249 control unit does not receive signals from the MID128 engine control unit through the SAE J1939 data channel. Broken or partial damage to the wires of the data channel. Between the blocks.
Parameter:
Communication failure by SAE J1939 data link with MID144 vehicle control unit
Fault:
FMI 9 The BBM MID249 control unit does not receive signals from the MID144 car control unit via the SAE J1939 data channel. Broken or partial damage to the wires of the data channel. Between theblocks.
Parameter:
Communication failure by SAE J1939 data link with dashboard control unit MID140
Fault:
FMI 9 The BBM MID249 control unit does not receive signals from the MID140 dashboard control unit via the SAE J1939 data channel. Broken or partial damage to the wires of the data channel. Between the blocks.
Parameter:
Communication violation by data channel SAE J1939 with braking system control unit MID136
Fault:
FMI 9 The BBM MID249 control unit does not receive signals from the MID136 braking system control unit via the SAE J1939 data channel. Broken or partial damage to the wires of the data channel.Between the blocks.
Parameter:
Communication failure by SAE J1939 data link with MID130 transaxle control unit
Fault:
FMI 9 The BBM MID249 control unit does not receive signals from the MID130 transmission control unit through the SAE J1939 data channel. Broken or partial damage to the wires of the data channel.Between the blocks.
Parameter:
Communication failure by SAE J1939 data link with MID223 selector control unit
Fault:
FMI 9 The VVM MID249 control unit does not receive signals from the MID223 transmission selector control unit via the SAE J1939 data channel. Broken or partial damage to the wires of the data channel.Between the blocks.
Parameter:
Communication failure by SAE J1939 data link with MID150 air suspension control unit
Fault:
FMI 9 The BBM MID249 control unit does not receive signals from the MID150 air suspension control unit via the SAE J1939 data channel. Broken or partial damage to the wires of the data channel.Between the blocks.
Parameter:
Communication failure by data channel SAE J1939 with air pressure regulation control unit
Fault:
FMI 9 The BBM MID249 control unit does not receive signals from the air pressure regulation control unit via the SAE J1939 data channel. Breakage or partial damage to the wires of the data channel between the blocks.
Parameter:
SAE J1939 data feed
Fault:
FMI 2 The BBM unit does not receive data, with the necessary update rate, from the body equipment. Open or partial damage to the data channel wires between the BBM unit and the external body equipment control unit.
FMI 9 The BBM unit does not receive data, with the required update rate, from the body equipment. Incorrect parameters, breakage or partial damage to the data channel wires between the BBM unit and the external body equipment control unit.
Parameter:
Software
Fault:
FMI 4 Incorrect software, power outages or strong electromagnetic interference.
FMI 5 Power was supplied to the BBM unit for at least 10 seconds with the ignition on, power supply interruptions, or the power supply circuit of the BBM power supply was broken.
FMI 12 Incorrect software, strong electromagnetic interference or defective BBM unit.
YTO Tractor owner's, service and maintenance manuals, tech specs, spare parts manuals & catalogs, wiring…
Yishan Bulldozer T160, T180, TS180, TSc180, TY160, TY180 and TY220 owner's, service and maintenance manuals,…
Wolf Garten Lawn Mower owner's, service and maintenance manuals, tech specs, spare parts manuals &…
Vermeer maintenance, service and operator's manuals in PDF for: heavy equipment, skid steer loaders, drill…
Venieri Wheel and Backhoe Loader: owner's, service and maintenance manuals, tech specs, spare parts manuals…
Valpadana Blitz 150, 4RM-180, 4RM-260, 4RM-350, 450, VP4600 and VP 7000-9000, 7060 and 7070 tractors:…