See also:
Parameter:
The status of the buttons on the steering wheel
Fault:
FMI 2 The fault code is registered only if the codes are active. PSID 17 , PSID 18 , SID 231 , SID 251 , SID 254 and disappears after troubleshooting these codes.
Parameter:
SAE J1939 data feed
Fault:
FMI 2 The SWM block registers a failure of the SAE J1939 data channel. Shorting the data channel wires to power or ground.
Parameter:
SWM power supply
Fault:
FMI 3 The power supply voltage of the SWM unit exceeds 36 V. for more than 5 seconds. Faulty generator or engine started from an external power source.
FMI 4 The power supply voltage of the SWM unit is below 9 V. for more than 5 seconds. An open circuit or short to ground.
Parameter:
SWM block
Fault:
FMI 12 SWM block defective.
Parameter:
“YES” button on the steering wheel
Fault:
FMI 12 The button is pressed for more than one minute or the button is faulty.
Parameter:
“NO” button on the steering wheel
Fault:
FMI 12 The button is pressed for more than one minute or the button is faulty.
Parameter:
Left arrow button on the steering wheel
Fault:
FMI 12 The button is pressed for more than one minute or the button is faulty.
Parameter:
Right Arrow Button on Steering Wheel
Fault:
FMI 12 The button is pressed for more than one minute or the button is faulty.
Parameter:
Steering wheel plus button
Fault:
FMI 12 The button is pressed for more than one minute or the button is faulty.
Parameter:
The minus button on the steering wheel
Fault:
FMI 12 The button is pressed for more than one minute or the button is faulty.
Parameter:
Power supply of the “YES, NO, plus, minus” buttons on the steering wheel
Fault:
FMI 3 The voltage at the output of the SWM block on the block of buttons above 14 V. more than 5 seconds. A short to a higher voltage of the wires between the SWM block and the button block.
FMI 4 The voltage at the output of the SWM block on the button block is below 7 V. for more than 5 seconds. Broken wire between the SWM unit and the button unit.
FMI 5 Broken wire between the SWM unit and the button unit.
FMI 6 The voltage at the output of the SWM block on the button block is less than 1 V for more than 5 seconds. A short to ground between the SWM block and the button block.
Parameter:
Data channel block buttons “YES, NO, plus, minus” on the steering wheel
Fault:
FMI 2 The SWM block does not receive the signal from the button block for more than 30 seconds, or the signal received from the button block is unreliable. Breakage or partial damage to the data channel wiring between the SWM block and the button block.
YTO Tractor owner's, service and maintenance manuals, tech specs, spare parts manuals & catalogs, wiring…
Yishan Bulldozer T160, T180, TS180, TSc180, TY160, TY180 and TY220 owner's, service and maintenance manuals,…
Wolf Garten Lawn Mower owner's, service and maintenance manuals, tech specs, spare parts manuals &…
Vermeer maintenance, service and operator's manuals in PDF for: heavy equipment, skid steer loaders, drill…
Venieri Wheel and Backhoe Loader: owner's, service and maintenance manuals, tech specs, spare parts manuals…
Valpadana Blitz 150, 4RM-180, 4RM-260, 4RM-350, 450, VP4600 and VP 7000-9000, 7060 and 7070 tractors:…