Allison Transmission 3000/4000 series fault code list

By | 16/05/2018

Allison Transmission 3000/4000 series fault code list – download PDF manual

See also: Allison Transmission PDF Service Manuals

Allison Transmission 3000/4000 Fault codes list Series

Allison Transmission 3000 Series

Allison Transmission Fault Codes PDF manuals

Allison 3000-4000 Series Troubleshooting Manual PDF
Allison Transmission 3000,4000 series fault code list PDF

Automatic transmissions Allison 3000 and 4000 Series with electronic control Gen4

Error code  

Description

Lamp

Check Trans

 

Reaction control system

C1312 Low voltage signal to the inclusion of retarder Off. Retarder is not included
C1313 High voltage signal at the inclusion of retarder Off. Retarder is not included
P0122 Intermittent or low level signal

accelerator pedal position

Off. The default value for

default

P0123 The high level of gas pedal position sensor signal Off. The default value for

default

P0218 Oil temperature too high Off. Sample control at excess temperature. Holds 4 transfer.Torque converter lock ban.

Disables adaptation

gear.

P0562 Low voltage control unit Off. Prohibition on blocking

the torque converter. DNA

P0602 The control unit is not programmed ON. Remains in neutral
P0610 Additional hardware error car with power

control

ON. The data are used

calibration of the TID (A)

P0613 Processor error control unit Off. All solenoids are turned off
P0614 Data incompatibility ECM and TCM for adjusting the moment the engine ON. Only neutral, back and second gear. Ban converter clutch switch adaption

is off

P0634 Temperature control unit exceeded ON. DNS, SOL OFF, actively

hydraulic control.

P063E There is no signal input on the situation of throttle

When flap auto definition

ON. The default value for

default

P063F There is no coolant temperature signal

Auto determination of

Off.
P0657 The gap chain Patients ON. SOL OFF DNA. Ban

torque converter lock, barring the master modulation.

P0658 Low voltage in the circuit of Patients ON. DNS, SOL OFF

hydraulic control active

P0659 High voltage in the circuit of Patients ON. DNS, SOL OFF

hydraulic control active

P0702 The control unit does not recognize AUTOMATIC configuration ON. Uses standard

configuration

P0703 There is a problem with the brake sensor Off. On musorovozah it is impossible to Enable N-D. If the code is active, the work is prohibited

retarder.

P0708 High level signal from the current transfer. ON Ignores the signal

poloskovogo switch

P070C Low oil level sensor signal Off.
P070D High level oil level sensor signal Off.
P0711 Adjunct oil temperature sensor signal ON. Uses the value of the

the default temperature

P0712 Low oil temperature sensor signal ON. Uses standard

the temperature value

P0713 The high level of oil temperature sensor signal ON. Uses standard

the temperature value

P0716 Adjunct of the turbine wheel speed sensor signal ON. DNS, the AUTOMATIC TRANSMISSION is blocked on

the current transfer

P0717 There is no signal to the turbine wheel speed sensor ON. DNS, the AUTOMATIC TRANSMISSION is blocked on

the current transfer

P0719 Low level signal sensor ABS braking Off. Considered ABS deactivated
P071A Incompatible input signal RELS ON. Function disables the RELS
P071D Wrong input signal a special function (wire

101 and 142)

ON.
P0721 Adjunct sensor signal output revolutions ON. DNS, the AUTOMATIC TRANSMISSION remains on

the current transfer

 

P0722 Output speed sensor no signal ON. DNS, the AUTOMATIC TRANSMISSION remains on

the current transfer

P0726 Non-standard engine speed sensor signal Off. Uses standard

turbine speed

P0727 Engine speed sensor no signal Off. Uses standard

turbine speed

P0729 Incorrect gear ratio on the 6-th transfer ON. DNS, tries to include 5-w,

then 3-n transfer

P0731 Incorrect gear ratio on the 1-th transfer ON. DNS, tries to include 2-w,

then 5-n transfer

P0732 Incorrect gear ratio on the 2-nd transfer ON. DNS, tries to include 3-w,

then 5-n transfer

P0733 Incorrect gear ratio to 3 s transfer ON. DNS, tries to include 4-th,

then the 6-th transfer

P0734 Incorrect gear ratio on the 4-th transfer ON. DNS, tries to include 5-w,

then 3-n transfer

P0735 Incorrect gear ratio on the 5-th transfer ON. DNS, tries to include 6-n,

then 3, then 2-n transfer

P0736 Incorrect gear ratio on the back of the transfer ON. DNS is blocked at neutral point
P0741 Slip clutch torque converter lock ON.
P0752 Sticking solenoid valve SS1 ON. DNS
P0776 Fault in the hydraulic diagram solenoid PCS2 ON. DNS, RPR
P0777 Fault in the hydraulic diagram solenoid PCS2 ON. DNS, RPR
P0796 Fault in the hydraulic diagram solenoid PCS3 ON. DNS, RPR
P0797 Fault in the hydraulic diagram solenoid PCS3 ON. DNS, RPR
P0842 Pressure sensor low voltage PS1. ON. DNS, the AUTOMATIC TRANSMISSION remains on

the current transfer

P0843 High pressure sensor voltage PS1. ON. DNS, the AUTOMATIC TRANSMISSION remains on

the current transfer

P0847 Pressure sensor low voltage PS2 ON.
P0848 High pressure sensor voltage PS2 ON.
P0880 Disappearance of power supply control unit during operation

engine

Off.
P0881 The voltage at the control unit is too low or jump Off.
P0882 The voltage at the control unit below normal ON. DNS, SOL OFF

hydraulic control active

P0883 The voltage at the control unit above the norm Off.
P088A Oil filter clogged Off.
P088B Oil filter severely beaten Off.
P0894 No passing moment in first gear ON. DNS remains at 1 transfer
P0897 Transmission oil needs to be replaced ON.
P0960 Open circuit solenoid valve pressure modulation ON.
P0962 Low voltage in the circuit pressure modulation solenoid valve ON. DNS, SOL OFF

hydraulic control active

P0963 High voltage in the circuit of solenoid valve modulation

pressure

ON
P0964 Open circuit solenoid PCS2 ON. DNS, SOL OFF

hydraulic control active

P0966 Low voltage in the circuit of solenoid PCS2 ON DNS, SOL OFF

hydraulic control active

 

P0967 High voltage in the circuit of solenoid PCS2 ON. DNS, SOL OFF

hydraulic control active

P0968 Open circuit solenoid PCS3 ON. DNS, SOL OFF

hydraulic control active

P0970 Low voltage in the circuit of solenoid PCS3 ON. DNS, SOL OFF

hydraulic control active

P0971 High voltage in the circuit of solenoid PCS3 ON. DNS, SOL OFF

hydraulic control active

P0973 Low voltage in the circuit of solenoid SS1 ON. DNS, SOL OFF

hydraulic control active

P0974 High voltage in the circuit of solenoid SS1 ON. DNS, SOL OFF

hydraulic control active

P0975 Open circuit solenoid SS2 ON. The 7-speed AUTOMATIC TRANSMISSION does not

Includes 1-7 and I-I transfer

P0976 Low voltage in the circuit of solenoid SS2 ON. The 7-speed AUTOMATIC TRANSMISSION are not included 1-7 and I-I

transmission torque converter lock ban

P0977 High voltage in the circuit of solenoid SS2 ON. The 7-speed AUTOMATIC TRANSMISSION does not

Includes 1-7 and I-I transfer

P0989 The signal from the retarder is disruption Off. Retarder is not included
P0990 Sensor signal retarder has short circuit Off. Retarder is not included
P1739 Incorrect gear ratio low-high ON. DNS, prohibition of work for 1

transfer

P1891 Accelerator pedal position sensor signal too low ON. Uses standard

value pressing the pedal

P1892 Accelerator pedal position sensor signal too high ON. Uses standard

value pressing the pedal

P2184 Low voltage temperature sensor signal

coolant

Off. Uses standard

the temperature value

P2185 High voltage temperature sensor signal

coolant

Off. Uses standard

the temperature value

P2637 Violation in torque control system

moment when you switch gears SEM

ON. Prohibition of work system of SEM
P2641 Violation of the constraint system on

lower gears LRTP

ON. Prohibition of work system of LRTP
P2669 The gap chain HSD2 ON. SOL OFF ban ban converter clutch

the main modulating DNA

P2670 Low voltage in the circuit HSD2 ON. DNS, SOL OFF

hydraulic control active

P2671 High voltage in the circuit HSD2 ON. DNS, SOL OFF

hydraulic control active

P2684 HSD3 open circuit ON. SOL OFF ban lock

the torque converter, ban the main DNA modulation

P2685 Low voltage in the circuit HSD3 ON. DNS, SOL OFF

hydraulic control active

P2686 High voltage in the circuit HSD3 ON. DNS, SOL OFF

hydraulic control active

P2714 Fault in the hydraulic diagram solenoid PCS4 ON. DNS, RPR
P2715 Fault in the hydraulic diagram solenoid PCS4 ON. DNS, SOL OFF

hydraulic control active

P2718 Open circuit solenoid PCS4 ON. DNS, SOL OFF

hydraulic control active

P2720 Low voltage in the circuit PCS4 solenoid ON. DNS, SOL OFF

hydraulic control active

P2721 High voltage in the circuit PCS4 solenoid ON. DNS, SOL OFF

hydraulic control active

P2723 Fault in the hydraulic diagram solenoid PCS1 ON. DNS, RPR
P2724 Fault in the hydraulic diagram solenoid PCS1 ON. DNS, RPR
P2727 Open circuit solenoid PCS1 ON. DNS, SOL OFF

hydraulic control active

P2729 Low voltage in the circuit of solenoid PCS1 ON. DNS, SOL OFF

hydraulic control active

P2730 High voltage in the circuit of solenoid PCS1 ON. DNS, SOL OFF

hydraulic control active

P2736 Open circuit solenoid PCS5 ON. Prohibition of work for retarder
P2738 Low voltage in the circuit PCS5 solenoid ON. Prohibition of work for the 1 St gear, retarder, locks work

the torque converter

P2739 High voltage in the circuit PCS5 solenoid ON. Prohibition of work for retarder
P2740 High oil temperature retarder Off.
P2742 Low oil temperature sensor signal

retarder

Off. Uses standard

the value of the oil temperature

P2743 The high level of oil temperature sensor signal

retarder

Off. Uses standard

the value of the oil temperature

P2761 Open circuit solenoid locking torque converter ON. Prohibition of lock

the torque converter

P2763 Low voltage in the circuit of solenoid lock

the torque converter

ON. Prohibition of lock

the torque converter

P2764 High voltage in the circuit of solenoid lock

the torque converter

ON. Prohibition of lock

the torque converter

P2789 Wear of the clutch reaches the limit value ON.
P278A Faulty signal Kickdown Off. The prohibition regime Kickdown
P2793 An error occurred while communicating with the switch gear ON. Ignores a PWM (pulse width modulation) signal via CAN-bus also lost, blocked

the last selected direction

P2808 Fault in the hydraulic diagram solenoid PCS6 ON DNS, RPR

 

P2809 Fault in the hydraulic diagram solenoid PCS6 Incl. DNS, RPR
P2812 Open circuit solenoid PCS6 Incl. DNS, SOL OFF

hydraulic control active

P2814 Low voltage in the circuit PCS6 solenoid Incl. DNS, SOL OFF

hydraulic control active

P2815 High voltage in the circuit PCS6 solenoid Incl. DNS, SOL OFF

hydraulic control active

U0001 High-speed counter overflow CAN-bus (IESCAN) Off. Uses standard values, ban torque management system when switching

gear

U0010 Counter overflow CAN-bus (IESCAN) Off. Uses standard values, ban torque management system when switching

gear

U0100 Loss of communication with the block of the engine/power unit (J1586) ON. Uses standard

the value of the

U0103 Loss of communication with the first switch gear ON. Remains in the selected broadcast, monitors signal a change of direction. Display goes off on

10 sec, then shows-/-/-

U0115 An error occurred while communicating with the engine control unit ON. Uses standard

DNA values

U0291 An error occurred while communicating with the secondary switch gear ON. Remains in the selected broadcast, monitors signal a change of direction. Display goes off on

10 sec, then shows-/-/-

U0304 Primary switch gear is not compatible with

J1939 Protocol

ON. DNS is blocked in neutral
U0333 Secondary switch is not compatible with the J1939 Protocol ON. DNS is blocked in neutral
U0400 Violation of J1939 data transmission ON.
U0404 Inadequate information with primary gear ON. Remains in the selected broadcast, monitors signal a change of direction. Display goes off on

10 sec, then shows-/-/-

U0442 The control unit receives incorrect information from the engine control unit/power unit included in the bus

J1939 data

Off.
U0592 Inadequate information from the secondary gear ON. Remains in the selected broadcast, monitors signal a change of direction. Display goes off on

10 sec, then shows-/-/-