Kalmar DRF 400-450 Engine Error Codes
See also:
Kalmar DRF 400-450
Error codes engine, general
When contacting engine suppliers, use Volvo/Cummins codes.
- Display indicates error code according to SAE J1939 SPN / FMI
- Flash indicates error code according to a flash code specified by the engine supplier.
- J1587 indicates error code according to SAE J1587 (for Volvo: Vodia).
PID, PPID, SID, PSID / FMI
Specification FMI
| FMI | Description | SAE-text |
| 0 | Too high value. | Valid data, but higher than normal operating range. |
| 1 | Too low value. | Valid data, but lower than normal operating range. |
| 2 | Incorrect data. | Intermittent or incorrect data. |
| 3 | Electric problem. | Abnormally high voltage or short-circuiting to higher voltage. |
| 4 | Electric problem. | Abnormally low voltage or short-circuiting to lower voltage. |
| 5 | Electric problem. | Abnormally low current or open circuit. |
| 6 | Electric problem. | Abnormally high current or short-circuiting to frame ground. |
| 7 | Mechanical problem. | Incorrect response from mechanical system. |
| 8 | Mechanical problem or electric problem. | Abnormal frequency. |
| 9 | Communication error. | Abnormal update rate. |
| 10 | Mechanical problem or electric problem. | Abnormally large variations. |
| 11 | Unknown error. | Non-identifiable error. |
| 12 | Component problem. | Defective unit or component. |
| 13 | Incorrect calibration. | Values outside calibration values. |
| 14 | Unknown error. | Special instructions. |
| 15 | Unknown error. | Reserved for future use. |
Error codes engine (engine alternative Volvo)
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 94/FMI | 3.6 | PID94/ FMI | Sensor fuel pres- sure short- circuited to volt- age, ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/2:3
Volvo TAD1250VE: D794/B:16 |
– |
| 94/FMI | 3.8 | PID94/ FMI | Low fuel pressure (feed). | No limitation. | Change fuel filter.
Change fuel prefilter. Check if pressure can be built up with the hand pump. |
– | – |
| 97/1 | 2.1 | PID97/ 1 | Water in fuel. | No limitation. | Drain water separator.
Clean metal filter in the fuel feed’s hose connection on the engine. Check fuel filter and fuel pre-filter. |
– | – |
| 97/3 | 2.9 | PID97/ 3 | Sensor water in fuel short- circuiting to ground or open circuit. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/2:4
Volvo TAD1250VE: D794/B:8 |
– |
| 98/FMI | 5.7 | PID98/ FMI | Low oil level. | No limitation. | Check oil level. | – | Engine, menu 6 |
| 98/FMI | 5.9 | PID98/ FMI | Sensor oil level short-circuiting to voltage, ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TAD1250VE: D794/B:3, B:4, A:31 | ENGINE,
menu 6 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 100/1 | 6.6 | PID100
/1 |
Low engine oil pressure. | Engine is shut off. | Check oil level. Change oil filter.
Check the system pressure valves and the safety valve in the lubrication system. Check the sensor. |
– | ENGINE,
menu 6 |
| 100/3 | 3.1 | PID100
/3 |
Sensor oil pressure cable short- circuited to volt- age. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:14
Volvo TAD1250VE: D794/B:11 |
ENGINE,
menu 6 |
| 100/4 | 3.1 | PID100
/4 |
Sensor oil pressure, open circuit, or short-circuiting to ground. | No limitation. | Check cable har- ness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:14
Volvo TAD1250VE: D794/B:11 |
ENGINE,
menu 6 |
| 102/0 | 3.5 | PID102
/0 |
Boost pressure too high. | No limitation. | Check the turbo- charger.
Check the sensor. Check fuel quality and injectors. |
– | ENGINE,
menu 6 |
| 102/1 | 3.5 | PID102
/1 |
Boost pressure too low. | Reduced engine power. | Check the air filter.
Check the turbo- charger. Check the sensor. Check the fuel feed pressure. |
– | ENGINE,
menu 6 |
| 102/3 | 3.4 | PID102
/3 |
Sensor boost pressure, cable short- circuited to volt- age. | Engine smokes more than normal during acceleration or when load- ed. | Check cable har- ness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:3
Volvo TAD1250VE: D794/A:22 |
ENGINE,
menu 7 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 102/4 | 3.4 | PID102
/4 |
Sensor boost pressure, cable short- circuited to ground or open circuit. | Engine smokes more than normal during acceleration or when load- ed. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:3
Volvo TAD1250VE: D794/A:22 |
ENGINE,
menu 7 |
| 105/0 | 6.2 | PID105
/0 |
High charge-air temperature. | Engine is shut off. | Check coolant level.
Check that the charge-air cooler is clean. Check thermostat. Check the sensor. |
– | ENGINE,
menu 7 |
| 105/3 | 3.2 | PID105
/3 |
Sensor charge-air temperature, cable short-circuited to voltage or open circuit. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:2
Volvo TAD1250VE: D794/A:47 |
ENGINE,
menu 7 |
| 105/4 | 3.3 | PID105
/4 |
Sensor charge-air temperature, cable short-circuited to ground or open circuit. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:2
Volvo TAD1250VE: D794/A:47 |
ENGINE,
menu 7 |
| 106/ FMI | 3.4 | PID106
/FMI |
Sensor boost pressure, short- circuiting to volt- age, frame ground, or open circuit. | Engine smokes more than normal during acceleration or when load- ed. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:3
Volvo TAD1250VE: D794/A:22 |
ENGINE,
menu 6 |
| 106/ FMI | 3.5 | PID106
/FMI |
Boost pressure too high. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
– | ENGINE,
menu 6 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 110/0 | 6.1 | PID110
/0 |
High coolant temperature. | Volvo TWD1240VE:
Engine is shut off. Volvo TAD1250VE: No limitation. |
Check coolant lev- el.
Check that radiator is clean. Check thermostat. Check the cap on the expansion tank. Check if there’s air in coolant system. Check the sensor. |
– | ENGINE,
menu 7 |
| 110/3 | 3.3 | PID110
/3 |
Sensor coolant temperature, cable short-circuited to voltage or open circuit. | Preheating is activated even if engine is warm. | Check cable har- ness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:25
Volvo TAD1250VE: D794/B:27 |
ENGINE,
menu 7 |
| 110/4 | 3.3 | PID110
/4 |
Sensor coolant temperature, cable short-circuited to ground. | Preheating is activated even if engine is warm. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:25
Volvo TAD1250VE: D794/B:27 |
ENGINE,
menu 7 |
| 111/1 | 2.2 | PID111
/1 |
Low coolant level. | Volvo TAD1250VE: Engine is shut off.
Volvo TAD1250VE: No limitation. |
Check the coolant level, top up if needed.
Check the sensor. |
– | – |
| 111/ FMI | 2.3 | PID111
/FMI |
Sensor coolant level, short- circuited to volt- age. | Volvo TWD1240VE:
Engine is shut off. Volvo TAD1250VE: No limitation. |
Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/2:7
Volvo TAD1250VE: D794/B:23 |
– |
| 153/ FMI | 7.7 | PID153
/FMI |
Crankcase ventilation pressure too high. | No limitation. | Clean crankcase ventilation.
Check wear of cylinder liner, piston, and piston rings. |
– | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 153/ FMI | 7.7 | PID153
/FMI |
Sensor crankcase ventilation pressure, short- circuiting to volt- age, frame ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TAD1250VE: D794/B:28 | – |
| 158/ FMI | 3.9 | PID158
/FMI |
Low battery volt- age. | Engine may be difficult to start. | Check and charge the batteries.
Check the alternator. Check the battery cables. |
– | – |
| 172/ FMI | 7.9 | PID172
/FMI |
Sensor air temperature inlet, short- circuited to voltage, ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:2
Volvo TAD1250VE: D794/A:47 |
ENGINE,
menu 7 |
| 175/0 | 5.8 | PID175
/0 |
High engine oil temperature. | Reduced engine power. | Check oil level.
Check the lubrication system’s thermostat. Check the sensor. |
– | ENGINE,
menu 7 |
| 175/3 | 3.7 | PID175
/3 |
Sensor oil temperature, cable short- circuited to voltage or open circuit. | No limitation. | Check cable har- ness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:1
Volvo TAD1250VE: D794/A:31, B:3, B:4 |
ENGINE,
menu 7 |
| 175/4 | 3.7 | PID175
/4 |
Sensor oil temperature, cable short- circuited to ground. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TWD1240VE: D794/1:1
Volvo TAD1250VE: D794/A:31, B:3, B:4 |
ENGINE,
menu 7 |
| 190/ FMI | 2.6 | PID190
/FMI |
Engine rpm too high. | No limitation. | Ease off throttle or select higher gear. | – | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 608/ FMI | – | PPID9 8/FMI | Signal error for start and stop. | No limitation. | Check CAN-bus drivetrain. | – | CAN/ POWER,
menu 3 |
| 620/3
1079/2 |
9.3 | SID232
/3 |
Voltage feed to sensors, cable short-circuited to voltage. | Several error codes for defective sensor.
Reduced engine power. Incorrect instrument values. |
Check cable harness between the control unit and the component. | Volvo TWD1240VE: D794/1:5
Volvo TAD1250VE: D794/B:17 |
– |
| 620/4
1079/3 |
9.3 | SID232
/4 |
Voltage feed to sensors, cable short-circuited to ground. | Several error codes for defective sensor.
Reduced engine power. Incorrect instrument values. |
Check cable harness between the control unit and the component. | Volvo TWD1240VE: D794/1:4
Volvo TAD1250VE. D794/B:17 |
– |
| 626/3 | 5.4 | PID45/ 3 | Preheating relay, cable short- circuited to volt- age. | Preheating can- not be activated. | Check cable harness between the control unit and the component.
Check the relay. |
Volvo TWD1240VE: D794/2:36
Volvo TAD1250VE: D794/B:25 |
ENGINE,
menu 5 |
| 626/4 | 5.4 | PID45/ 4 | Preheating relay, cable short- circuited to ground. | Preheating is al- ways activated. | Check cable harness between the control unit and the component.
Check the relay. |
Volvo TWD1240VE: D794/2:36
Volvo TAD1250VE: D794/B:25 |
ENGINE,
menu 5 |
| 626/5 | 5.4 | PID45/ 5 | Preheating relay open circuit on cable or defective component. | Preheating can- not be activated. | Check cable harness between the control unit and the component.
Check the relay. |
Volvo TWD1240VE: D794/2:36
Volvo TAD1250VE: D794/B:25 |
ENGINE,
menu 5 |
| 629/ FMI | 9.9 | SID254
/FMI |
Control unit engine (D794) internal error. | Engine doesn’t start.
Engine runs rough. |
Change the control unit. | – | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 630/ FMI | 9.9 | SID253
/FMI |
Control unit engine (D794) memory error. | Engine doesn’t start. | Re-program the control unit. | – | – |
| 636/3 | 2.5 | SID21/3 | Sensor rpm camshaft, no signal. | Engine takes longer time to start than normal. Engine runs normally when it has started. | Check cable harness between the control unit and
the component. Check the sensor. |
Volvo
TWD1240VE: D794/1:7, 1:18 Volvo TAD1250VE: D794/B:45, B:46 |
– |
| 636/8 | 2.5 | SID21/8 | Sensor engine rpm, camshaft, abnormal frequency. | Engine takes longer time to start than normal. Engine runs normally when it has started. | Check cable harness between the control unit and
the component. Check the sensor. |
Volvo
TWD1240VE: D794/1:7, 1:18 Volvo TAD1250VE: D794/B:45, B:46 |
– |
| 637/2 | 2.4 | SID22/2 | Sensor engine rpm, flywheel, irregular signal. | Engine is extremely difficult to start and runs
rough, if it starts. |
Check cable harness between the control unit and
the component. Check the sensor. |
Volvo
TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 |
ENGINE,
menu 2 |
| 637/3 | 2.4 | SID22/3 | Sensor engine rpm, flywheel, abnormal frequency. | Engine is extremely difficult to start and runs
rough, if it starts. |
Check cable harness between the control unit and
the component. Check the sensor. |
Volvo
TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 |
ENGINE,
menu 2 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 630/ FMI | 9.9 | SID253
/FMI |
Control unit engine (D794) memory error. | Engine doesn’t start. | Re-program the control unit. | – | – |
| 636/3 | 2.5 | SID21/3 | Sensor rpm camshaft, no signal. | Engine takes longer time to start than normal. Engine runs normally when it has started. | Check cable harness between the control unit and
the component. Check the sensor. |
Volvo
TWD1240VE: D794/1:7, 1:18 Volvo TAD1250VE: D794/B:45, B:46 |
– |
| 636/8 | 2.5 | SID21/8 | Sensor engine rpm, camshaft, abnormal frequency. | Engine takes longer time to start than normal. Engine runs normally when it has started. | Check cable harness between the control unit and
the component. Check the sensor. |
Volvo
TWD1240VE: D794/1:7, 1:18 Volvo TAD1250VE: D794/B:45, B:46 |
– |
| 637/2 | 2.4 | SID22/2 | Sensor engine rpm, flywheel, irregular signal. | Engine is extremely difficult to start and runs
rough, if it starts. |
Check cable harness between the control unit and
the component. Check the sensor. |
Volvo
TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 |
ENGINE,
menu 2 |
| 637/3 | 2.4 | SID22/3 | Sensor engine rpm, flywheel, abnormal frequency. | Engine is extremely difficult to start and runs
rough, if it starts. |
Check cable harness between the control unit and
the component. Check the sensor. |
Volvo
TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 |
ENGINE,
menu 2 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 637/8 | 2.4 | SID22/
8 |
Sensor engine rpm, flywheel, abnormal frequency. | Engine is extremely difficult to start and runs rough, if it starts. | Check cable harness between the control unit and the component. Check that the sensor is correctly connected. | Volvo
TWD1240VE: D794/1:30, 1:31 Volvo TAD1250VE: D794/B:37, B:38 |
ENGINE, menu 2 |
| 639/FMI
2017/FMI |
6.5 | SID231/FMI
PSID201/FMI |
Communication error with Engine control unit (D794), configuration error. | Engine off: engine cannot be started.
Engine on: engine goes to idle and can only be stopped by using the emergency stop. |
Use diagnostic menu to find incorrect segment.
Check cable harness between the control unit and the component. Check the control unit. |
Volvo
TWD1240VE: D794/2:1, 2:2 Volvo TAD1250VE: D794/B:51, B:55 |
CAN/ POWER, menu 3 |
| 639/FMI | 6.4 | SID231
/FMI |
Communication error with Engine control unit (D794), configuration error. | Instruments and controls do not work. | Use diagnostic menu to find incorrect segment.
Check cable har- ness between the control unit and the component. Check the control unit. |
– | CAN/ POWER,
menu 3 |
| 639/FMI | 9.9 | SID240
/FMI |
Memory error engine control unit. | It may not be possible to start the engine. | Re-program the control unit. | – | – |
| 651/2 | 7.1 | SID1/2 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 651/3 | 7.1 | SID1/3 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 |
– |
| 651/4 | 7.1 | SID1/4 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 |
– |
| 651/5 | 7.1 | SID1/5 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 |
– |
| 651/7 | 7.1 | SID1/7 | Incorrect compression or defective injector cylinder 1. | Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance. Check cable harness between the control unit and
the component. Check the injector. Perform compression test and check cylinder 1. |
Volvo TWD1240VE: D794/1:11, 1:12
Volvo TAD1250VE: D794/A:20, A:24 |
– |
| Description | Limitation | Action | Connection and compo- nent | Diag- nostic menu | |||
| Code | Flash | J1587 | |||||
| 651/11 | 7.1 | SID1/11 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:11, 1:12 Volvo TAD1250VE: D794/A:20, A:24 |
– |
| 652/2 | 7.2 | SID2/2 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:20, A:24 |
– |
| 652/3 | 7.2 | SID2/3 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 |
– |
| 652/4 | 7.2 | SID2/4 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 |
– |
| 652/5 | 7.2 | SID2/5 | Electric failure, injector cylinder 1. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 652/7 | 7.2 | SID2/7 | Incorrect compression or defective injector cylinder 2. | Runs rough at low rpms and low load. | Check fuel pressure.
Check valve clearance. Check cable harness between the control unit and the component. Check the injector. Perform compression test and check cylinder 2. |
Volvo TWD1240VE: D794/1:22, 1:12
Volvo TAD1250VE: D794/A:12, A:16 |
– |
| 652/11 | 123DTC7.2 | SID2/
11 |
Electric failure, injector cylinder 2. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:22, 1:12 Volvo TAD1250VE: D794/A:12, A:16 |
– |
| 653/2 | 7.3 | SID3/2 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
Volvo
TWD1240VE: D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 |
– |
| 653/3 | 7.3 | SID3/3 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE. D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 653/4 | 7.3 | SID3/4 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component.
Check the injector. |
Volvo TWD1240VE: D794/1:23, 1:12
Volvo TAD1250VE: D794/A:28, A:32 |
– |
| 653/5 | 7.3 | SID3/5 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component.
Check the injector. |
Volvo TWD1240VE: D794/1:23, 1:12
Volvo TAD1250VE: D794/A:28, A:32 |
– |
| 653/7 | 7.3 | SID3/7 | Incorrect compression or defective injector cylinder 3. | Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance. Check cable harness between the control unit and
the component. Check the injector. Perform compression test and check cylinder 3. |
Volvo TWD1240VE: D794/1:23, 1:12
Volvo TAD1250VE: D794/A:28, A:32 |
– |
| 653/11 | 7.3 | SID3/11 | Electric failure, injector cylinder 3. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:23, 1:12 Volvo TAD1250VE: D794/A:28, A:32 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 654/2 | 140
DTC 7.4 |
SID4/2 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 |
– |
| 654/3 | 7.4 | SID4/3 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component. Check the injector. | Volvo TWD1240VE:
D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 |
– |
| 654/4 | 7.4 | SID4/4 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 |
– |
| 654/5 | 7.4 | SID4/5 | Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 654/7 | 7.4 | SID4/7 | Incorrect compression or defective
injector cylinder 4. |
Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance. Check cable harness between the control unit and
the component. Check the injector. Perform compression test and check cylinder 4. |
Volvo TWD1240VE: D794/1:34, 1:24
Volvo TAD1250VE: D794/A:52, A:56 |
– |
| 654/11 | 7.4 | SID4/
11 |
Electric failure, injector cylinder 4. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:34, 1:24 Volvo TAD1250VE: D794/A:52, A:56 |
– |
| 655/2 | 7.5 | SID5/2 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 |
– |
| 655/3 | 7.5 | SID5/3 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 655/4 | 7.5 | SID5/4 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component.
Check the injector. |
Volvo TWD1240VE: D794/1:35, 1:24
Volvo TAD1250VE: D794/A:44, A:48 |
– |
| 655/5 | 7.5 | SID5/5 | Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable har- ness between the control unit and the component.
Check the injector. |
Volvo TWD1240VE: D794/1:35, 1:24
Volvo TAD1250VE: D794/A:44, A:48 |
– |
| 655/7 | 7.5 | SID5/7 | Incorrect compression or defective injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check that cabling to the injectors is not damaged. Check cable harness between the control unit and
the component. Check the injector. Perform compression test and check cylinder 5. |
Volvo
TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 |
– |
| 655/11 | 7.5 | SID5/
11 |
Electric failure, injector cylinder 5. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:35, 1:24 Volvo TAD1250VE: D794/A:44, A:48 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 656/2 | 7.6 | SID6/2 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the component. |
Volvo
TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 |
– |
| 656/3 | 7.6 | SID6/3 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 |
– |
| 656/4 | 7.6 | SID6/4 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 |
– |
| 656/5 | 7.6 | SID6/5 | Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and
the component. Check the injector. |
Volvo
TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VE: D794/A:36, A:40 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 656/7 | 7.6 | SID6/7 | Incorrect compression or defective
injector cylinder 6. |
Runs rough at low rpms and low load. | Check fuel pressure. Check valve clearance.
Check cable harness between the control unit and the component. Check the injector. Perform compression test and check cylinder 6. |
Volvo TWD1240VE: D794/1:36, 1:24
Volvo TAD1250VE: D794/A:36, A:40 |
– |
| 656/11 | 7.6 | SID6/
11 |
Electric failure, injector cylinder 6. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component. Check the injector. | Volvo
TWD1240VE: D794/1:36, 1:24 Volvo TAD1250VED 794/A:36, A:40 |
– |
| 677/
FMI |
6.3 | PPID3/
FMI SID39/ FMI |
Starter motor re-lay, short-circuiting to voltage ground. | Engine doesn’t start.
Engine starts immediately when ignition is turned on. |
Check cable harness between the control unit and the component. Check the motor. | Volvo
TWD1240VE: D794/2:31 Volvo TAD1250VED 794/B:29 |
ENGINE,
menu 5 |
| 1485/3 | 5.1 | PPID5/ 3 | Main relay, cable short-circuited to voltage. | Instrument panel loses voltage when ignition key is turned to start position. Engine doesn’t start. | Check cable harness between the control unit and the component.
Check the relay. |
Volvo TWD1240VE: D794/1:32
Volvo TAD1250VE: D794/A:8 |
– |
| 2791/ FMI | – | PPID1 9/FMI | Internal EGR, electric problem or mechanical problem. | No limitation. | Check sensor boost pressure.
Check the component. (IEGR) Contact Volvo Penta workshop for more information. |
Volvo TAD1250VE: D794/B:30 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 52019
2/FMI |
6.8 | PPID8/ FMI | Sensor piston cooling pressure short-circuiting to voltage, ground, or open circuit. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
Volvo TAD1250VE: D794/B:14 | – |
| 52019
2/FMI |
6.7 | PPID8/
FMI |
Low piston cooling pressure. | No limitation. | Check that engine’s oil pressure is higher than 175
kPa. |
– | – |
| 52019
5/FMI |
4.8 | PPID4/ FMI | Stop input on control unit short-circuits to ground or open circuit. | Engine cannot be shut off. | Check cable harness between the control unit and the component. | Volvo TWD1240VE: D794/2:6
Volvo TAD1250VE: D794/B:27 |
– |
Error codes engine (engine alternative Cummins QSM11)
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 84/2 | 241 | PID08
4/2 |
Electric problem sensor speed, data invalid. | Engine rpm restricted to max. rpm without gear. | Check cable harness between the control unit and the component.
Check the sensor. |
– | – |
| 84/10 | 242 | PID08 4/10 | Electric problem sensor speed, manipulation of signal detected. | Engine rpm restricted to max. rpm without gear. | Check cable harness between the control unit and the component.
Check the sensor. |
– | – |
| 91/3 | 131 | PID09
1/3 |
Electric problem throttle pedal, cable short-circuited to voltage. | Engine does not respond to throttle. | Check cable harness between the control unit and the component.
Check the component. |
– | – |
| 91/4 | 132 | PID09
1/4 |
Electric problem throttle pedal, cable short-circuited to ground. | Engine does not respond to throttle. | Check cable harness between the control unit and the component.
Check the component. |
– | – |
| 91/8 | 147 | PID09
1/8 |
Electric problem throttle pedal, frequency too low. | Engine does not respond to throttle. | Check cable harness between the control unit and the component.
Check the component. |
– | – |
| 91/8 | 148 | PID09
1/8 |
Electric problem throttle pedal, frequency too high. | Engine does not respond to throttle. | Check cable harness between the control unit and the component.
Check the component. |
– | – |
| 91/19 | 287 | SID09
1/2 |
Communication error with Cab control unit (D790-1), electric problem throttle pedal. | Engine only runs on idle. | Use diagnostic menu to localize incorrect segment. | – | CAN/ POWER,
menu 3 |
| 97/3 | 428 | PID09
7/3 |
Electric problem sensor water in fuel, cable short- circuited to voltage. | No limitation. | Check cable harness between the control unit and the component.
Check the component. |
D794/Sen- sor:09 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 97/4 | 429 | PID09
7/4 |
Electric problem sensor water in fuel, cable short- circuited to ground. | No limitation. | Check cable harness between the control unit and the component.
Check the component. |
D794/Sen- sor:09 | – |
| 97/15 | 418 | PID09 7/15 | Water in fuel. | Risk of white exhaust smoke and reduced engine power. | Drain water from the fuel filter. | – | – |
| 100/1 | 415 | PID10
0/1 |
Low engine oil pressure. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check oil level in the engine, top up as need- ed. | – | ENGINE,
menu 6 |
| 100/2 | 435 | PID10
0/2 |
Sensor oil pressure, data error. | No warning for low oil pressure engine. | Check the sensor. | D794/Sen- sor:44 | ENGINE,
menu 6 |
| 100/3 | 135 | PID10
0/3 |
Sensor oil pressure cable short- circuited to voltage. | No warning for low oil pressure engine. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sen- sor:44 | ENGINE,
menu 6 |
| 100/4 | 141 | PID10
0/4 |
Sensor oil pressure, open circuit, or short-circuiting to ground. | No warning for low oil pressure engine. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/
Black:14 |
ENGINE,
menu 6 |
| 100/
18 |
143 | PID10
0/1 |
Low engine oil pressure. | No limitation. | Check oil level in the engine, top up as need- ed.
Check the sensor. |
– | ENGINE,
menu 6 |
| 102/2 | 433 | PID10
2/2 |
Sensor boost pressure indicates high boost pressure, but other engine data indicate that pressure should be nor- mal. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sen- sor:39 | ENGINE,
menu 7 |
| 102/3 | 122 | PID10
2/3 |
Sensor boost pressure, cable short- circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sen- sor:39 | ENGINE,
menu 7 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 102/4 | 123 | PID10
2/4 |
Sensor boost pressure, cable short- circuited to ground or open circuit. | Reduced engine power. | Check cabling between control unit and component.
Check sensor boost pressure. |
D794/
Black:3 |
ENGINE,
menu 7 |
| 103/
16 |
595 | PID10
3/0 |
Overspeed protection turbo. | Reduced engine power. | Check the component. | – | – |
| 105/0 | 155 | PID10
5/0 |
Inlet air too warm. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check the coolant level in the engine, top up as needed.
Check that the charge- air cooler is clean, clean as needed. Check that the fan belts are intact. Check sensor inlet air temperature. |
– | ENGINE,
menu 7 |
| 105/3 | 153 | PID10
5/3 |
Sensor charge-air temperature, cable short-circuited to voltage or open circuit. | Risk of white exhaust smoke. No warning for high coolant temperature. | Check cabling between control unit and component.
Check that sensor charge-air temperature is installed correctly and connected. Check sensor charge- air temperature. |
D794/Sen- sor:38 | ENGINE,
menu 7 |
| 105/4 | 154 | PID10
5/4 |
Sensor charge-air temperature, cable short-circuited to ground or open circuit. | Risk of white exhaust smoke. No warning for high coolant temperature. | Check cable harness between the control unit and the component.
Check that sensor is in- stalled correctly and connected. Check the sensor. |
D794/Sen- sor:38 | ENGINE,
menu 7 |
| 108/2 | 295 | PID10
8/2 |
Electric problem sensor air pressure, data error. | Reduced engine power. | Check the sensor. | – | – |
| 108/3 | 221 | PID10
8/3 |
Electric problem air pressure, cable short-circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sensor:06 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 108/4 | 222 | PID10
8/4 |
Electric problem air pressure, cable short-circuited to ground. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sen- sor:06 | – |
| 110/0 | 151 | PID11
0/0 |
High coolant temperature. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check coolant level.
Check that radiator is clean. Check if there’s air in coolant system. Check the cap on the expansion tank. Check the sensor. Check thermostat. |
– | ENGINE,
menu 7 |
| 110/3 | 144 | PID11
0/3 |
Sensor coolant temperature, cable short-circuited to voltage or open circuit. | No display of engine temperature. | Check cable harness between the control unit and the component. | D794/Sen- sor:02 | ENGINE,
menu 7 |
| 110/4 | 145 | PID11
0/4 |
Sensor coolant temperature, cable short-circuited to ground. | No display of engine temperature. | Check cable harness between the control unit and the component.
Check that the sensor is correctly connected. Check the sensor. |
D794/Sen- sor:02 | ENGINE,
menu 7 |
| 111/1 | 235 | PID11
1/1 |
Low coolant level. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check the coolant level, top up if needed.
Check the sensor. |
– | – |
| 111/2 | 422 | PID11
1/2 |
Electric problem sensor coolant lev- el, data error. | No warning for low coolant level. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sen- sor:09 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 166/2 | 951 | PID11
6/2 |
Power imbalance between cylinders. | Rough idling. | Check the fuel quality. If the fuel system has been opened so that air may have entered the system, the error code may be generated.
Troubleshoot the engine. |
– | – |
| 167/1 | 598 | PID16
7/1 |
Low battery volt- age. | Warning active until voltage is correct. | Check batteries and alternator. | D794/ OEM:7, 8,
17, 18, 28 |
– |
| 167/
16 |
596 | PID16
7/0 |
Low battery volt- age. | Warning active until voltage is correct. | Check fuses. Check batteries and alternator. | D794/ OEM:7, 8,
17, 18, 28 |
– |
| 167/
18 |
597 | PID16
7/1 |
High battery volt- age. | Warning active until voltage is correct, engine runs at high idle to increase volt- age. | Check batteries and alternator. | D794/ OEM:7, 8,
17, 18, 28 |
– |
| 168/
16 |
442 | PID16
8/0 |
Voltage feed to control unit high. | No limitation. | Check fuses. Check batteries and alternator. | D794/ OEM:7, 8,
17, 18, 28 |
– |
| 168/
18 |
441 | PID16
8/1 |
Voltage feed to control unit low. | Rough idling. | Check fuses. Check batteries and alternator. | D794/ OEM:7, 8,
17, 18, 28 |
– |
| 175/0 | 214 | PID17
5/0 |
High engine oil temperature. | Engine power drops gradually, after 30 seconds the engine is shut off. | Check coolant level and oil level in engine, top up as needed.
Check that the oil cooler is clean, clean as need- ed. Check that the fan belts are intact. Check the sensor. |
– | ENGINE,
menu 7 |
| 175/3 | 212 | PID17
5/3 |
Sensor oil temperature, cable short- circuited to voltage or open circuit. | No display of oil temperature engine. | Check cable harness between the control unit and the component.
Check that the sensor is correctly connected. |
D794/Sen- sor:42 | ENGINE,
menu 7 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 175/4 | 213 | PID17
5/4 |
Sensor oil temperature, cable short- circuited to ground. | No display of oil temperature engine. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sen- sor:42 | ENGINE,
menu 7 |
| 188/4 | 466 | SID03
2/4 |
Electric problem solenoid valve wastegate 1 short- circuiting to ground. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
D794/Actuator: 24 | |
| 190/0 | 234 | PID19
0/0 |
Engine rpm too high. | Fuel feed is restricted until engine rpm is below permitted rpm. | Ease off throttle or select higher gear. | – | – |
| 190/2 | 115 | PID19
0/2 |
Electric problem sensor rpm/ignition position, no signal from any of the sensors. | Engine stops and cannot be started. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sen- sor:47, 50 | – |
| 190/
10 |
121 | PID19 0/10 | Electric problem sensor rpm/ignition position, on of two signals is missing. | No limitation. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sensor: 47, 50 | – |
| 191/
16 |
349 | PID19
1/0 |
Speed limitation activated. | Speed is reduced. | Ease off throttle. | – | – |
| 191/
18 |
489 | PID19
1/1 |
Speed warning for low speed. | Engine only runs on idle. | Increase throttle. | – | – |
| 251/2 | 319 | PID25
1/2 |
Internal error Control unit engine. | – | – | – | – |
| 441/3 | 293 | PID44
1/3 |
Extra sensor temperature short- circuited to ground. | No warning at high temperature Control unit engine (D794). | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sensor: 12 | |
| 441/4 | 294 | PID44
1/4 |
Extra sensor temperature short- circuited to voltage. | No warning at high temperature Control unit engine (D794). | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sensor: 12 | |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 558/2 | 431 | SID23
0/2 |
Electric problem sensor throttle ped- al, idle switch data error. | No limitation. | Check cable between control unit and component.
Check component. |
D794/ OEM: 03,
13 |
– |
| 558/4 | 551 | SID23
0/4 |
Electric problem sensor throttle ped- al, idle switch cable short-circuited to ground. | Engine does not respond to throttle. | Check cable between control unit and compo- nent.
Check component. |
D794/ OEM: 03,
13 |
– |
| 558/
13 |
432 | SID23 0/13 | Electric problem sensor throttle ped- al, idle switch calibration error. | Engine only runs on idle. | Check cable between control unit and component.
Check component. |
D794/ OEM: 13 | – |
| 608/2 | 412 | SID25
0/2 |
Communication error with Control unit engine (D794). | No limitation. | Check the control unit. | D794/ OEM: 26,
27, 36, 37, 46 |
|
| 608/9 | 414 | SID25
0/9 |
Communication error with Control unit engine (D794). | No limitation. | Check the control unit. | D794/ OEM: 26,
27, 36, 37, 46 |
|
| 620/3
1080/ 3 |
227 | SID23
2/3 |
Electric problem reference voltage to sensor short- circuited to voltage. | Reduced engine power. No warning low oil pressure or low coolant level. | Check cable harness between the control unit and the component.
Check the control unit. |
D794/Sensor: 18, 25,
45 |
– |
| 620/4
1081/ 4 |
187 | SID23
2/4 |
Electric problem reference voltage to sensor short- circuited to ground. | Reduced engine power. No warning low oil pressure or low coolant level. | Check cable harness between the control unit and the component.
Check the component. |
D794/Sensor: 18, 25,
45 |
– |
| 626/
11 |
381 | SID23 7/11 | Electric problem to control of relay pre- heating. | Preheating does not work. Risk of white smoke | Check cable harness between the control unit and the component.
Check the component. |
D794/Actuator: 34 | ENGINE,
menu 5 |
| 627/2 | 434 | SID25
1/2 |
Voltage feed to control unit disappears without engine off. | Reduced engine power. Engine difficult to start or engine stops. | Check fuses.
Check batteries and alternator. |
D794/ OEM:7, 8,
17, 18, 28 |
– |
| 629/
12 |
111 | SID25 4/12 | Internal error Control unit engine. | Engine doesn’t start. | Check the control unit. | – | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 629/
12 |
343 | SID25 4/12 | Internal error Control unit engine. | No limitation. | Check the control unit. | – | – |
| 630/2 | 341 | SID25
3/2 |
Software error control unit, engine (D794). | Reduced engine power. Engine difficult to start or engine stops. | Re-program the soft- ware in Control unit engine (D794). | – | – |
| 632/3 | 255 | SID01
7/3 |
Electric problem solenoid valve fuel shut-off, cable short-circuited to voltage. | No limitation. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
D794/Actuator: 33 | – |
| 632/4 | 254 | SID01
7/4 |
Electric problem solenoid valve fuel shut-off, cable short-circuited to ground. | Engine is shut off. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
D794/Actuator: 33 | – |
| 639/2 | 426 | SID23
1/2 |
Communication error with Control unit engine (D794). | Functions via CAN-bus do not work. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER,
menu 2 |
| 639/9 | 427 | SID23
1/9 |
Communication error with Control unit engine (D794). | Functions via CAN-bus do not work. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER,
menu 2 |
| 639/9 | 285 | SID23
1/9 |
Communication error with Engine control unit (D794), timeout error. | Functions via CAN-bus do not work. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER,
menu 2 |
| 639/
13 |
286 | SID23 1/13 | Communication error with Engine control unit (D794), configuration error. | Functions via CAN-bus do not work. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER,
menu 2 |
| 644/2 | 237 | SID03
0/2 |
Electric problem throttle pedal, signal outside valid range. | Engine is shut off. | Check cable harness between the control unit and the component.
Check the component. |
– | – |
| 647/4 | 245 | SID03
3/4 |
Electric problem fan connection, cable short-circuited to ground. | Cooling fan al- ways driven. | Check cable harness between the control unit and the component.
Check the component. |
D794/Ac-
tuator:10, Actuator: 9 |
– |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 651/5 | 322 | SID00
1/5 |
Electric problem injector cylinder 1, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator:10, Actuator: 9 | – |
| 651/6 | 311 | SID00
1/7 |
Electric problem injector cylinder 1, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator:10, Actuator: 9 | – |
| 652/5 | 331 | SID00
2/5 |
Electric problem injector cylinder 2, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator: 7, 8 | – |
| 652/6 | 315 | SID00
2/6 |
Electric problem injector cylinder 2, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator:7, 8 | – |
| 653/5 | 324 | SID00
3/5 |
Electric problem injector cylinder 3, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator:6, 16 | – |
| 653/6 | 313 | SID00
3/6 |
Electric problem injector cylinder 3, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable between control unit and component.
Check component. |
D794/Actuator:6, 16 | – |
| 654/5 | 332 | SID00
4/5 |
Electric problem injector cylinder 4, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator:26, 36 | – |
| 654/6 | 321 | SID00
4/6 |
Electric problem injector cylinder 4, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator:26, 36 | – |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 655/5 | 323 | SID00
5/5 |
Electric problem injector cylinder 5, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator: 3, 4 | – |
| 655/6 | 312 | SID00
5/6 |
Electric problem injector cylinder 5, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable between control unit and component.
Check component. |
D794/Actuator: 3, 4 | – |
| 656/5 | 325 | SID00
6/5 |
Electric problem injector cylinder 6, open circuit on cable. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable between control unit and component.
Check component. |
D794/Actuator: 1, 2 | – |
| 656/6 | 314 | SID00
6/6 |
Electric problem injector cylinder 6, cable short- circuited to ground. | Engine runs on 5 cylinders, sounds rough and has reduced power. | Check cable harness between the control unit and the component.
Check the injector. |
D794/Actuator: 1, 2 | – |
| 702/3 | 527 | SID04
0/3 PID15 4/3 |
Electric problem extra output 2, cable short-circuited to voltage | No limitation. | Check cable harness between the control unit and the component.
Check the component. |
D794/Actuator: 14 | – |
| 703/3 | 529 | SID05
1/3 |
Electric problem extra output 2, cable short-circuited to voltage | No limitation. | Check cable harness between the control unit and the component.
Check the component. |
D794/Actuator: 45 | – |
| 974/3 | 133 | SID02
9/3 |
Electric problem extra throttle pedal, cable short- circuited to voltage. | Engine does not respond to throttle. | Check cable harness between the control unit and the component.
Check the component. |
D794/ OEM: 21 | – |
| 974/4 | 134 | SID02
9/4 |
Electric problem extra throttle pedal, cable short- circuited to ground. | Engine does not respond to throttle. | Check cable harness between the control unit and the component.
Check the component. |
D794/ OEM: 21 | – |
| 974/
19 |
288 | SID02
9/2 |
Communication error with Cab control unit (D790-1), electric problem throttle pedal. | Engine does not respond to throttle. | Use diagnostic menu to find incorrect segment. | – | CAN/ POWER,
menu 2 |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 1043/
3 |
387 | PID22
1/3 |
Electric problem throttle pedal reference voltage, cable short-circuited to voltage. | Engine only runs on idle. | Check cable harness between the control unit and the component.
Check the component. |
D794/ OEM: 48 | – |
| 1043/
4 |
443 | PID22
1/4 |
Electric problem throttle pedal reference voltage, cable short-circuited to ground. | Engine only runs on idle. | Check cable harness between the control unit and the component.
Check the component. |
D794/ OEM: 48 | – |
| 1072/
11 |
388 | SID07 0/11 | Electric problem solenoid valve engine brake 2. | Engine brake 1 cannot be activated. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
D794/Actuator: 44 | – |
| 1073/
11 |
392 | SID02 9/11 | Electric problem solenoid valve engine brake 2. | Engine brake 2 cannot be activated. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
D794/Actuator: 44 | – |
| 1079/
3 |
386 | SID23
2/3 |
Electric problem reference voltage to sensor short- circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sesor: 17, 37 | – |
| 1079/
4 |
352 | SID23
2/4 |
Electric problem reference voltage to sensor short- circuited to ground. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sen- sor: 17, 37 | – |
| 1188/
3 |
465 | SID03
2/3 |
Electric problem solenoid valve wastegate 1 short- circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
D794/Actuator: 24 | – |
| 1189/
3 |
491 | SID08
8/3 |
Electric problem solenoid valve wastegate 2 short- circuited to voltage. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
D794/Actuator: 23 | |
| Description | Limitation | Action | Connection and component | Diagnostic menu | |||
| Code | Flash | J1587 | |||||
| 1189/
4 |
492 | SID88/ 4 | Electric problem solenoid valve wastegate 2 short- circuited to ground. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
D794/Actuator: 23 | |
| 1265/
4 |
223 | SID08
5/4 |
Electric problem solenoid valve oil- burn, cable short- circuited to ground. | No limitation. | Check cable harness between the control unit and the component.
Check the solenoid valve. |
– | – |
| 1319/
2 |
419 | PID10
2/2 |
Electric problem sensor boost pressure. | Reduced engine power. | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sensor: 9 | – |
| 1380/
1 |
219 | PID01
7/1 |
Low oil level engine. | No limitation. | Check oil level in the engine, top up as need- ed. | – | – |
| 1383/
31 |
611 | SID15 1/11 | Engine shut off in another way than with start key means loading. | No limitation. | Shut off the engine with the start key. | – | – |
| 1384/
31 |
299 | SID02 9/14 | Engine shut off in another way than with start key means loading. | No limitation. | Shut off the engine with the start key. | – | – |
| 1387/
3 |
297 | PID22
3/3 |
Electric problem extra sensor pressure, cable short- circuited to voltage. | No protection for pressure (customer-specific option). | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sesor: 19 | – |
| 1387/
4 |
298 | PID22
3/4 |
Electric problem extra sensor pressure, cable short- circuited to ground. | No protection for pressure (customer-specific option). | Check cable harness between the control unit and the component.
Check the sensor. |
D794/Sesor: 19 | – |
| 1484/
31 |
211 | SID21 6/11 | Error codes in other control units. | No limitation. | Check error codes for the other control units on the machine, primarily Control unit cab (D790-1) and Control unit transmission (D793). | – | – |
