Deciphering the diagnostic trouble codes of the MID130 TECU Volvo gearbox control units .
See also:
MID 130 PID 31
Parameter:
Position of the range cylinder
The sensor is located in the control box of the gearbox; it registers the highest and the lowest gears of the range amplifier (LR and HR).
Fault:
FMI 3 A short in the sensor circuit to power.
FMI 5 Open sensor circuit.
FMI 6 Short circuit sensor to ground.
FMI 13 The position sensor is not calibrated.
MID 130 PID 32
Parameter:
The position of the cylinder divider. The sensor is located in the control box of the gearbox; it registers the highest and the lowest gears of the divider (LS and HS).
Fault:
FMI 3 A short in the sensor circuit to power.
FMI 5 Open sensor circuit.
FMI 6 Short circuit sensor to ground.
FMI 13 The position sensor is not calibrated.
MID 130 PID 33
Parameter:
Clutch cylinder position. The position sensor is located in the clutch cylinder.
Fault:
FMI 3 A short in the sensor circuit to power.
FMI 5 Open sensor circuit.
FMI 13 The position sensor is not calibrated.
MID 130 PID 36
Parameter:
Clutch disc wear
Fault:
FMI 0 Worn disc clutch exceeds acceptable value.
MID 130 PID 37
Parameter:
Air pressure. The sensor is located in the control box of the gearbox.
Fault:
FMI 0 Air pressure above 9.2 bar. The pneumatic pressure regulator is faulty or the sensor is faulty.
FMI 1 Air pressure below 4.5 bar. The pneumatic components are not tight, the pneumatic pressure regulator is faulty, or the sensor is faulty.
FMI 3 The sensor signal voltage is higher than 4.5 V. A short in the sensor circuit to power or a sensor is faulty.
FMI 5 The sensor signal voltage is less than 0.5 V. A break in the sensor circuit wires or a sensor is faulty.
MID 130 PID 124
Parameter:
Oil level in the gearbox.
Fault:
FMI 0 Low oil level, sensor open circuit or sensor malfunction.
MID 130 PID 127
Parameter:
Transmission oil pressure
Fault:
FMI 1, 5 Transmission oil pressure low or sensor faulty. Shorting wires in the sensor circuit. An open circuit in the sensor circuit or a pressure sensor is faulty.
MID 130 PID 158
Parameter:
Voltage at the input to the battery control unit
Fault:
FMI 0 Voltage exceeds 32 V. for more than 1 second. Faulty generator or external power supply to start the engine.
FMI 1 Voltage below 21.5 V with the engine running for more than 60 seconds. Faulty generator.
MID 130 PID 160
Parameter:
The frequency of rotation of the main shaft. The sensor is located in the control box of the gearbox.
Fault:
FMI 4 The sensor signal voltage is less than 0.5 V. The voltage drop in the sensor circuit or the sensor is faulty.
FMI 5 Shorting or breaking wires in the sensor circuit. The sensor may be faulty.
MID 130 PID 161
Parameter:
The frequency of rotation of the primary shaft.
Fault:
FMI 3 Shorting the wires in the sensor circuit to power.
FMI 5 An open circuit in the sensor circuit.
FMI 6 Shorting the wires in the sensor circuit to ground.
FMI 8 The distance to the rotation sensor above normal.
MID 130 PID 177
Parameter:
Transmission oil temperature.
Fault:
FMI 0 The oil temperature is above +110 degrees for at least 5 seconds or the sensor is faulty.
FMI 4 Shorting the wires in the sensor circuit to ground.
FMI 5 An open or short to power to the wires in the sensor circuit.
MID 130 PID 190
Parameter:
Engine speed
Fault:
FMI 3 Shorting the wires in the sensor circuit to power.
FMI 5 An open circuit in the sensor circuit.
FMI 6 Shorting the wires in the sensor circuit to ground.
FMI 8 The distance to the rotation sensor above normal.
MID 130 PID 191
Parameter:
Output speed
Fault:
FMI 3 Shorting the wires in the sensor circuit to power.
FMI 5 An open circuit in the sensor circuit.
FMI 6 Shorting the wires in the sensor circuit to ground.
FMI 8 The distance to the rotation sensor above normal.
MID 130 SID 1
Parameter:
Solenoid valve S1. The valve is located in the control box gearbox.
Fault:
FMI 5 Open circuit in one of the valves S1 or S8. A short circuit in the circuit of one of the valves S1 or S8 to the power supply.
FMI 6 Short circuit in the S1 valve circuit to ground.
MID 130 SID 2
Parameter:
Solenoid valve S2. The valve is located in the control box gearbox.
Fault:
FMI 5 An open in the S2 valve circuit. A short circuit in the S2 valve circuit is energized.
FMI 6 A short circuit in the S2 valve circuit is grounded.
MID 130 SID 3
Parameter:
Electromagnetic valve S3. The valve is located in the control box gearbox.
Fault:
FMI 5 Open circuit in one of the valves S3 or S4. A short to one of the S3 or S4 valves is connected to power.
FMI 6 Short circuit in the S3 valve circuit to ground.
MID 130 SID 4
Parameter:
Solenoid valve S4. The valve is located in the control box gearbox.
Fault:
FMI 5 Open circuit in one of the valves S3 or S4. A short to one of the S3 or S4 valves is connected to power.
FMI 6 Short circuit in the S4 valve circuit to ground.
MID 130 SID 5
Parameter:
Solenoid valve S5. The valve is located in the control box gearbox.
Fault:
FMI 5 Open circuit in one of the valves S5 or S7. A short circuit in the circuit of one of the S5 or S7 valves to the power supply.
FMI 6 Short circuit in the S5 valve circuit to ground.
MID 130 SID 7
Parameter:
Solenoid valve of wide-pulse modulation (PWM) S14. The valve is located in the control box gearbox.
Fault:
FMI 5 An open circuit in one of the PWM S14 or S-RET valves (retarder valve) or an open R08B jumper.
MID 130 SID 8
Parameter:
S7 solenoid valve, forward clutch. The valve is located in the control box gearbox.
Fault:
FMI 5 Open circuit in one of the valves S5 or S7. A short circuit in the circuit of one of the S5 or S7 valves to the power supply.
FMI 6 Short circuit in the S7 valve circuit to ground.
MID 130 SID 35
Parameter:
High Range Range Solenoid Valve (HR). The valve is located in the control box gearbox.
Fault:
FMI 3 A short circuit in the control unit on the power supply.
FMI 5 Open or short in control unit.
FMI 6 A short to ground in the control unit.
MID 130 SID 36
Parameter:
Low Range Solenoid Valve (LR) Solenoid Valve. The valve is located in the control box gearbox.
Fault:
FMI 3 A short circuit in the control unit on the power supply.
FMI 5 Open or short in control unit.
FMI 6 A short to ground in the control unit.
MID 130 SID 37
Parameter:
High Solenoid Valve (HS) solenoid valve. The valve is located in the control box gearbox.
Fault:
FMI 3 A short circuit in the control unit on the power supply.
FMI 5 Open or short in control unit.
FMI 6 A short to ground in the control unit.
MID 130 SID 38
Parameter:
Solenoid valve for low range divider (LS). The valve is located in the control box gearbox.
Fault:
FMI 3 A short circuit in the control unit on the power supply.
FMI 5 Open or short in control unit.
FMI 6 A short to ground in the control unit.
MID 130 SID 231
Parameter:
SAE J1939 data feed
Fault:
FMI 2 No data available. Broken wire data channel, damaged or oxidized contacts in the connectors or faulty control unit.
MID 130 SID 240
Parameter:
Program memory
Fault:
FMI 2 Error in the program. Program the gearbox control unit.
MID 130 SID 250
Parameter:
SAE J1708 data feed
Fault:
FMI 2 Too many invalid messages sent over the data channel for a certain period of time. Partial damage to the data channel wires or oxidized contacts in the connectors.
FMI 4 Open circuit, short to ground or to power supply, data channel wires.
MID 130 SID 253
Parameter:
Gauge memory
Fault:
FMI 2 Error programming calibration memory or faulty control unit.
MID 130 PPID 10
Parameter:
The position of the cylinder 1 gear. The sensor is used to register the first, reverse gear and neutral position. Located in the control building.
Fault:
FMI 3 A short in the sensor circuit to power.
FMI 5 An open in the sensor circuit.
FMI 6 Short circuit in the sensor circuit to ground.
FMI 13 The sensor is not calibrated.
MID 130 PPID 50
Parameter:
Load clutch disc.
Fault:
FMI 0 Wrong choice of gear at the beginning of the movement. In order to avoid slippage in the clutch, it is necessary to choose the right gear to start moving. Do not press hard on the accelerator pedal.
MID 130 PPID 51
Parameter:
Clutch engagement position.
Fault:
FMI 13 Clutch engagement position not calibrated.
MID 130 PPID 54
Parameter:
Power +5 V clutch position sensor from the control unit.
Fault:
FMI 0 Voltage higher than 6 V. A short in the wiring between the control unit and the clutch cylinder.
FMI 1 Voltage below 4 V. A short in the wiring between the control unit and the clutch cylinder.
MID 130 PPID 55
Parameter:
Temperature control unit.
Fault:
FMI 0 Temperatures above +125 degrees. Check for oil in the gearbox.
MID 130 PPID 140
Parameter:
Tilt angle. The angle sensor is located in the control box.
Fault:
FMI 2 Short or open in the angle sensor circuit. The sensor may be faulty.
MID 130 PSID 1
Parameter:
Rapid firing valve (PWM valve).
Fault:
FMI 3 Open or short to power in clutch cylinder circuit.
FMI 5 Open or short to power in clutch cylinder circuit.
FMI 6 Open circuit or short to ground in the clutch cylinder circuit.
MID 130 PSID 3
Parameter:
Quick off valve (KlapanShIM).
Fault:
FMI 3 Open or short to power in clutch cylinder circuit.
FMI 5 Open or short to power in clutch cylinder circuit.
FMI 6 Open circuit or short to ground in the clutch cylinder circuit.
MID 130 PSID 4
Parameter:
Slow Shut Off Valve .
Fault:
FMI 3 Open or short to power in clutch cylinder circuit.
FMI 5 Open or short to power in clutch cylinder circuit.
FMI 6 Open circuit or short to ground in the clutch cylinder circuit.
MID 130 PSID 5
Parameter:
Mass valves quickly PWM on and off
Fault:
FMI 3 Open or short to power in clutch cylinder circuit.
FMI 5 Open or short to power in clutch cylinder circuit.
FMI 6 Open circuit or short to ground in the clutch cylinder circuit.
MID 130 PSID 6
Parameter:
Weight of PWM valves of slow on and off
Fault:
FMI 3 Open or short to power in clutch cylinder circuit.
FMI 5 Open or short to power in clutch cylinder circuit.
FMI 6 Open circuit or short to ground in the clutch cylinder circuit.
MID 130 PSID 12
Parameter:
The solenoid valve of the internal position of the cylinder 1 includes the first transmission and the transition to the neutral position. The valve is located in the control gear case.
Fault:
FMI 3 A short to power in the control unit. The control unit is located in the control box of the gearbox.
FMI 5 An open or short to power in the gearbox control unit.
FMI 6 A short to ground in the gearbox control unit.
MID 130 PSID 13
Parameter:
The solenoid valve for the external position of the cylinder 1 reverse gear and transfer the neutral position. The valve is located in the control gear case.
Fault:
FMI 3 A short to power in the control unit. The control unit is located in the control box of the gearbox.
FMI 5 An open or short to power in the gearbox control unit.
FMI 6 A short to ground in the gearbox control unit.
MID 130 PSID 14
Parameter:
The solenoid valve of the internal position of the cylinder 2 includes the second gear and the neutral position. The valve is located in the control gear case.
Fault:
FMI 3 A short to power in the control unit. The control unit is located in the control box of the gearbox.
FMI 5 An open or short to power in the gearbox control unit.
FMI 6 A short to ground in the gearbox control unit.
MID 130 PSID 15
Parameter:
The solenoid valve of the external position of the cylinder 2 includes the third gear and the transition to the neutral position. The valve is located in the control gear case.
Fault:
FMI 3 A short to power in the control unit. The control unit is located in the control box of the gearbox.
FMI 5 An open or short to power in the gearbox control unit.
FMI 6 A short to ground in the gearbox control unit.
MID 130 PSID 20
Parameter:
Solenoid valve PTO number 1. Usually located behind the left front wheel in front of the battery box.
Fault:
FMI 3 Shorting the wires in the valve circuit to the power supply.
FMI 5 Open or short in valve circuit for power.
FMI 6 Shorting the wires in the valve circuit to ground or short inside the valve.
MID 130 PSID 21
Parameter:
Solenoid PTO number 2. Usually located behind the left front wheel in front of the battery box.
Fault:
FMI 3 Shorting the wires in the valve circuit to the power supply.
FMI 5 Open or short in valve circuit for power.
FMI 6 Shorting the wires in the valve circuit to ground or short inside the valve.
MID 130 PSID 22
Parameter:
Solenoid brake intermediate valve. Located in the control box gearbox.
Fault:
FMI 3 A short to power in the control unit. The control unit is located in the control box of the gearbox.
FMI 5 An open or short to power in the gearbox control unit.
FMI 6 A short to ground in the gearbox control unit.
MID 130 PSID 30
Parameter:
TMS data channel. The TMS channel is similar to the SAE J1939 data channel, used only for data exchange between the transmission control unit (MID130) and the gear selector control unit MID223.
Fault:
FMI 2 Missing data. Damage to the wires of the data channel or the oxidation of contacts in the connectors. There may be a malfunction in the control unit.
FMI 9 Data is updated at low speed. No power to the MID223 selector control unit. The MID223 selector control unit is in programming mode. Damage to the wires of the data channel or the oxidation of contacts in the connectors. There may be a malfunction in the control unit.
MID 130 PSID 100
Parameter:
Slip clutches in the gearbox.
Fault:
FMI 0 Stuck solenoid valves, low oil pressure in the gearbox or clutch discs burned.
FMI 1 Stuck solenoid valves, low oil pressure in the gearbox or clutch discs burned.
FMI 7 Stuck solenoid valves or low gearbox oil pressure.
MID 130 PSID 101
Parameter:
Slip clutches, clutch lock.
Fault:
FMI 0 Slipping of the clutch of blocking of the torque converter when switching on, positive torque. Jamming valve PWM S14 locking torque converter.
FMI 1 Slipping the clutch locking torque converter when you turn on, negative torque. Jamming valve PWM S14 locking torque converter.
FMI 7 Slipping the clutch locking torque converter in other situations. Seat valve PWM S14 lock torque converter.
MID 130 PSID 102
Parameter:
Solenoid valve S8. clutch reverse gear.
Fault:
FMI 5 Open or short to power in the circuits of one of the solenoid valves S1 or S8.
FMI 6 A short to ground in the S8 solenoid circuit.
MID 130 PSID 103
Parameter:
Valve PWM S11 basic pressure.
Fault:
FMI 5 Open or short to power in the circuit of one of the PWM valves S11 or S13.
MID 130 PSID 104
Parameter:
Valve PWM S13, braking pressure.
Fault:
FMI 5 Open or short to power in the circuit of one of the PWM valves S11 or S13.
MID 130 PSID 105
Parameter:
Solenoid valve power take-off.
Fault:
FMI 5 Open or short to voltage in the solenoid valve circuit.
FMI 6 A short to ground in the solenoid valve circuit.
MID 130 PSID 200
Parameter:
Communication failure by SAE J1939 data link with MID128 engine control module.
Fault:
FMI 9 The data waiting time from the engine control unit over the SAE J1939 data channel has expired. Damaged or oxidized pins in connectors. Data channel wiring is damaged. The control unit may befaulty.
MID 130 PSID 201
Parameter:
Communication failure by SAE J1939 data link with vehicle control unit MID144.
Fault:
FMI 8 The information received from the car control unit is erroneous. There may be faults in the accelerator pedal sensor or in the brake pedal switch.
FMI 9 The data waiting time from the vehicle control unit via the SAE J1939 data channel has expired. Damaged or oxidized pins in connectors. Data channel wiring is damaged. The control unit may befaulty.
MID 130 PSID 204
Parameter:
Communication violation by data channel SAE J1939 with braking system control unit MID136
Fault:
FMI 8 The information received from the braking system control unit is erroneous. There may be faults in wheel speed sensors. Check the trouble codes in the braking system control unit (EBS / ABS MID136).
FMI 9 Data waiting time from the braking system control unit via data channel SAE J1939 has expired. Damaged or oxidized pins in connectors. Data channel wiring is damaged. The control unit may be faulty.
MID 130 PSID 207
Parameter:
SAE J1939 data link disruption with MID223 gear selector control unit
Fault:
FMI 9 gearbox control unit peredachv for 5 seconds is not receiving signals via SAE J1939 data from the control unit selector switch MID223 transmission. Broken or partial damage to the wires of the data channel. Between the blocks.
MID 130 PSID 210
Parameter:
Communication failure by SAE J1939 data link with MID216 outdoor lighting control unit
Fault:
9 FMI block transmission control within 5 seconds does not receive the channel SAE J1939 data from external lighting control unit MID216. Broken or partial damage to the wires of the data channel. Between the blocks.
MID 130 PSID 254
Parameter:
DIEE signal.
Fault:
FMI 3 Closing the input signal to the power supply.
I love this I am so interested,with Volvo