MID220 diagnostic trouble codes for Volvo FH tachograph
See also:
- MID219 ACC Volvo Cruise Control Fault Codes
- MID216 Volvo LCM outdoor lighting control unit fault codes
MID 220 SID 231
Parameter:
SAE J1939 data feed
Fault:
FMI 2 Open or shorted SAE J1939 data channel wires.
FMI 12 Vehicle control unit MID144 is not responding. There is no power to the car control unit MID144.
MID 220 SID 240
Parameter:
Program memory
Fault:
FMI 2 Internal error in the tachograph.
MID 220 SID 251
Parameter:
Tachograph power supply
Fault:
FMI 3, 4, 12 The tachograph supply voltage is above or below the normal voltage range. The contacts in the connectors are oxidized or damaged, the loss of the tachograph power supply, the voltage drop during the starter operation, poor contact on the battery terminals.
MID 220 SID 252
Parameter:
Calibration Module
Fault:
FMI 12 Calibration error detected. Faulty cable or connector device for programming the tachograph. Faulty device for programming the tachograph.
MID 220 SID 253
Parameter:
Gauge EEPROM Memory
Fault:
FMI 2 Internal error in the tachograph.
MID 220 PSID 1
Parameter:
Ignition off, a speed signal is present.
Fault:
FMI 8 The tachograph detects pulses from the speed sensor when the ignition is off. The car is moving, the contacts in the connectors, the breakage or short circuit of the wires between the speed sensor and the tachograph, are oxidized or damaged, a malfunction in the supply of the tachograph voltage.
MID 220 PSID 2
Parameter:
Registration block error
Fault:
FMI 2 Tachograph malfunction or error between the programming device and the tachograph. During the calibration of the tachograph, the ignition was turned off, the power supply of the tachograph or the programming device was interrupted. A loss of connection between the tachograph and the programming device has occurred.
MID 220 PSID 3
Parameter:
Request for adjustment hours
Fault:
FMI 2 In the tachograph revealed an error of time. The time shown by the tachograph does not coincide with the real time.
MID 220 PSID 4
Parameter:
Speed signal
Fault:
FMI 2 No speed signal pulses. Oxidized or damaged contacts in the connectors. An open or short to ground for the signal wire. Power interruption. Internal error in the input signal from the car control unit Internal error in the output signal of the tachograph.
MID 220 PSID 6
Parameter:
Speed sensor, communication line
Fault:
FMI 2 Communication error between the tachograph unit (connector B3) and the speed sensor. An open or short circuit between the speed sensor and the tachograph, the contacts in the speed sensor or tachograph connector are oxidized or damaged, the speed sensor is faulty.
FMI 9 Communication error between the tachograph unit (connector B4) and the speed sensor. An open or short circuit between the speed sensor and the tachograph, the contacts in the speed sensor or tachograph connector are oxidized or damaged, the speed sensor is faulty.
FMI 12 Speed sensor defective.
FMI 14 Communication error between tachograph unit and speed sensor. Missing or invalid pulse from the speed sensor. Open or short circuit between the speed sensor and tachograph, the contacts in the speed sensor or tachograph connector are oxidized or damaged, the speed sensor is faulty, the gear wheel in the transmission is damaged.
MID 220 PSID 7
Parameter:
Tachograph buttons
Fault:
FMI 7 One or several buttons on the tachograph panel stuck or was pressed for more than 3 minutes.
MID 220 PSID 8
Parameter:
Print device
Fault:
FMI 12 The power source of the print device inside the tachograph is faulty or the temperature of the head of the print device is out of set limits. Wait a while for the head to cool. Restart the print device by disconnecting it from the power supply (A1 connector).
FMI 14 Out of paper in print device.
MID 220 PSID 9
Parameter:
Tachograph display
Fault:
FMI 12 Malfunction in display or internal error in data transfer to display.
MID 220 PSID 10
Parameter:
Card reader error number 1
Fault:
FMI 12 The contact surfaces of the card are dirty or damaged. Check the surface of the card. Check tachograph by inserting another card.
MID 220 PSID 11
Parameter:
Card reader failure.
Fault:
Mechanical malfunction of the card reader or damaged card.
MID 220 PSID 12
Parameter:
Speed sensor power supply
Fault:
FMI 3, 4, 5 No power to speed sensor. The contacts in the speed sensor or tachograph connectors are damaged or oxidized, the wires between the speed sensor and the tachograph are broken or shorted, the speed sensor power supply wire is shorted to ground, the speed sensor loses power when the engine is started. Probably defective speed sensor.
MID 220 PSID 13
Parameter:
Riding without a card
Fault:
FMI 14 While driving, there is no card in the number 1 card reader or an invalid card is inserted.
MID 220 PSID 14
Parameter:
Installing the card, driver number 1
Fault:
FMI 14 Card identity verification errors or data security checks. The personal code of the service station mechanic is entered incorrectly 5 times. After a power outage or power failure, is missing or replaced with another previously installed card. Error when removing the card from the tachograph of the previous car. The universal time in the tachograph of the previous car is different from the time in this tachograph. The card was inserted after the start of the vehicle. Possibly invalid card.
MID 220 PSID 15
Parameter:
Installing the card, driver number 2
Fault:
FMI 14 Card identity verification errors or data security checks. The personal code of the service station mechanic is entered incorrectly 5 times. After a power outage or power failure, is missing or replaced with another previously installed card. Error when removing the card from the tachograph of the previous car. The universal time in the tachograph of the previous car is different from the time in this tachograph. The card was inserted after the start of the vehicle. Possibly invalid card.
MID 220 PSID 22
Parameter:
Speed sensor, mismatch
Fault:
FMI 14 Faulty or fake speed sensor. The speed sensor is not compatible with the tachograph. Contacts in the speed sensor or tachograph connectors are damaged. Open or short circuit between tachograph and speed sensor. Perform the procedure of combining the speed sensor and the tachograph (requires a special device for programming).
MID 220 PSID 24
Parameter:
Tachograph tray
Fault:
FMI 14 Tray for registration washer remained open with the ignition off.
MID 220 PSID 25
Parameter:
Paper compartment
Fault:
FMI 14 The paper compartment is open when the card is removed or opened during printing.
MID 220 PSID 26
Parameter:
Event No. 1
Fault:
FMI 14 Warning after continuous movement for 4 hours. 15 min.
MID 220 PSID 27
Parameter:
Event # 2
Fault:
FMI 14 Warning after continuous movement for 4 hours. 30 min.
MID 220 PSID 28
Parameter:
Event # 3
Fault:
FMI 2 Short-term excess of the programmed maximum speed.
FMI 14 Exceeding the programmed maximum speed for more than 60 seconds.
MID 220 PSID 29
Parameter:
Registration device
Fault:
FMI 12 There are no signals from the photocell. Internal fault in the tachograph. Repair or replace the tachograph.
MID 220 PSID 30
Parameter:
Registration device
Fault:
FMI 12 There are no signals from the photocell. Internal fault in the tachograph. Repair or replace the tachograph.
MID 220 PSID 202
Parameter:
Data Link Disruption SAE J1939 with dashboard control unit MID140
Fault:
FMI 9 The tachograph unit does not receive signals from the MID140 dashboard control unit over the SAE J1939 data channel. Breakage or partial damage to the wires of the data channel between the blocks.
