INS Error Codes list for Mercedes-Benz Trucks Actros, Axor, Atego
See also:
List of diagnostic trouble codes (DTCs) of the toolbar block (INS) for Mrcedes-Benz Actros, Atego, Axor
0101 Sensor supply “Filling pressure in circuit 1” has a short to ground
0102 Sensor supply “Filling pressure in circuit 1” has a short to positive
0104 Sensor signal input “Filling pressure in circuit 1” does not reach the measurement area
0105 Input signal from the sensor “Filling pressure in circuit 1” exceeds the measurement range
0201 Sensor supply “Filling pressure in circuit 2” has a short to ground
0202 Sensor supply “Filling pressure in circuit 2” has a short to positive
0204 Sensor input signal “Filling pressure in circuit 2” does not reach the measurement area
0205 Sensor input signal “Filling pressure in circuit 2” exceeds the measurement range
0301 Cab locking system has a short to ground
0308 Cab locking system has open or short to positive
0508 The fuel level sensor in the fuel tank has an open or short to positive
0607 Input Terminal W has a short to ground or open circuit.
0901 Cable K has a short to ground
0902 Cable K has an open or short to positive.
1020 Malfunction of car CAN bus
1101 Digital input X1.18 / 12 unreliable
OR
The state of the digital input X1.18 / 1 “Front center lock” unreliable
1102 Digital input X1.18 / 11 unreliable
OR
The state of the digital input X1.18 / 2 “Differential lock 1. The front axle” unreliable
1103 Digital input X1.18 / 10 unreliable
OR
The state of digital input X1.18 / 3 “Stock of washer agent” is unreliable
1104 Digital input X3.18 / 11 unreliable
OR
The state of the digital input X1.18 / 4 “Differential lock 1. Rear axle” unreliable
1105 The state of the digital input X1.18 / 5 “Differential lock 2. Front Axle” unreliable
1106 The state of the digital input X1.18 / 6 “Locking the driver’s cabin on the left” unreliable
1107 The state of digital input X1.18 / 7 “Differential lock 2. Rear axle” unreliable
1108 The state of the digital input X1.18 / 8 “Rear center lock” unreliable
1109 Digital input X1.18 / 9 unreliable
OR
The state of the digital input X1.18 / 9 “Locking the driver’s cab on the right” is unreliable
1110 Digital input X1.18 / 10 unreliable
1111 Digital input X1.18 / 11 “Power take-off” status unreliable
1112 Digital input X1.18 / 12 unreliable
1113 The state of digital input X1.18 / 13 “Control lamps” unreliable
1114 The state of digital input X1.18 / 14 “Oil level in the steering mechanism” is unreliable
1115 The state of the digital input X1.18 / 15 “Fault ABS trailer” unreliable
1116 The state of the digital input Х2.18 / 9 “Contact in the door” is unreliable
1117 The state of the digital input X3.18 / 11 “Steering with hydraulic booster” unreliable
1118 The state of digital input X3.18 / 12 “Filling pressure in circuit 4” is unreliable
1119 The state at the input X3.18 / 13 “Terminal 58” unreliable
1120 The state of digital input X3.18 / 14 “Reserve” is unreliable
1121 State of digital input X3.18 / 16 “Filling pressure in circuit 3” is invalid
1122 Back Zurück button status is invalid
1123 Down Auf button status invalid
1124 The status of the button “Up Ab” unreliable
1125 Auswahl Select button status is invalid
1126 The “Reset Reset” button status is invalid
1127 The Plus Plus button status is invalid
1128 The status of the button “Minus Minus” unreliable
1129 “Set Set” button status invalid
1130 The state of the button “Select Select” is invalid
1131 The state of the digital input Х2.18 / 5 “Terminal 15” is unreliable
1220 Connection failure between K-module and n-module
1321 Parameter Error in K-Module
1332 K-module is faulty
1333 K-module is faulty
1421 Parameter error in control unit
OR
Parameter error in n-module
1432 Internal error in control unit
OR
n-module is faulty
1520 CAN bus on tachograph faulty
OR
V-signal from the FR control unit is missing
1903 Terminal 15 is open
1941 Overvoltage
OR
Overvoltage at terminal 15
1942 Insufficient voltage at terminal 15
2001 Communication with the control unit at address 1 is broken
2002 Communication with the FR control unit is broken.
2003 Communication with the control unit at address 3 is broken
2004 Communication with the control unit at address 4 is broken
2005 Communication with the SPA control unit broken
2006 Communication with the PFA control unit broken
2007 Communication with FLA control unit broken
2008 Communication with the KS control unit broken
2009 Communication with the GS control unit is broken
2010 Communication with the control unit at address 10 is broken
2011 Communication with the SIR control unit is broken
2012 Data communication with the SIL control unit broken
2013 Data communication with WSK control unit broken
2014 Communication with the ABS control unit is broken
2015 Data communication with the RS control unit is broken
2016 Communication with the control unit at address 16 is broken
2017 Communication with the NR control unit is broken
2018 Communication with the FFB control unit is broken
2019 Communication with the ZV or KSA control unit is faulty
2020 Communication with the EKL control unit is broken
2021 Communication with the control unit at address 21 is broken
2022 Communication with the control unit at address 22 is broken
2023 Communication with the control unit at address 23 is broken
2024 Communication with the WS control unit is broken.
2025 Communication with the control unit at address 25 is broken
2026 Data communication with the control unit KOM broken
2027 Communication with the control unit at address 27 is broken
2028 Communication with the HZR control unit is faulty
2029 Communication with the ZHE control unit is faulty
2030 Communication with the control unit at address 30 is broken
2031 Communication with the HPS control unit is faulty
2032 Communication with the control unit at address 32 is broken
2033 Communication with the control unit at address 33 is broken
2034 Communication with the control unit at address 34 is broken
2035 Communication with the control unit at address 35 is broken
2036 Communication with the BS control unit is broken
2037 Communication with the control unit at address 37 is broken
2038 Communication with the AGE control unit is broken.
2039 Communication with the control unit at address 39 is broken
2040 Communication with the MR control unit is broken.
2041 Communication with the control unit at address 41 is broken
2042 Communication with the SRS control unit is faulty
2043 Communication with the control unit at address 43 is broken
2044 Communication with the EDW control unit is broken.
2045 Communication with the control unit at address 45 is broken
2046 Communication with the PSM control unit is broken
2047 Communication with the SRB control unit is broken.
2048 Communication with the control unit at 48 is broken
2049 Communication with the ART control unit is broken.
OR
Communication with the control unit at 49 is broken
2050-2099 Data communication with the control unit at addresses from 50 to 99 is broken
2100 Communication with the AGE control unit is broken
2101-2104 Communication with the control unit at addresses from 101 to 104 is broken
2105 Communication with the ANH control unit is broken.
2106-2109 Communication with the control unit at addresses from 106 to 109 is broken
2110 Communication with the AUF control unit is broken
2111-2199 Data communication with the control unit at addresses from 111 to 199 is broken
2515 Nor any text data is not embedded in the toolbar
3001 The control unit at address 1 is not working
3002 FR control unit defective
3003 The control unit at address 3 is not healthy
3004 The control unit at address 4 is not working
3005 SPA control unit out of order
OR
The control unit at address 5 is not working
3006 PFA control module is out of order
3007 FLA control unit out of order
3008 GS control unit defective
OR
KS control unit not working
3009 GS control unit defective
3010 The control unit at address 10 is not working
3011 SIR control module not working
3012 SIL control unit not working
3013 WSK control unit defective
3014 ABS control unit defective
3015 RS control unit out of order
3016 The control unit at address 16 is not working
3017 NR control unit not working
3018 FFB control module not working
3018 ZV or KSA control unit is defective
3020 EKL control unit out of order
3021-3023 The control unit at addresses from 21 to 23 is not working
3024 WS control unit not working
3025 The control unit at address 25 is not working
3026 KOM control unit not working
3027 The control unit at address 27 is not working
3028 HZR control unit is defective
3029 ZHE control unit not working
3030 The control unit at address 30 is not working
3031 HPS control module is defective
3032-3035 The control unit at addresses from 32 to 35 is not working
3036 BS control unit is not working
3037 The control unit at address 37 is not working
3038 AGE control unit is defective
3039 The control unit at address 39 is not working
3040 MR control unit not working
3041 The control unit at address 41 is not working
3042 SRS control unit out of order
3043 The control unit at address 43 is not working
3044 EDW control unit defective
3045 The control unit at address 45 is not working
3046 PSM control unit defective
3047 SRB control unit out of order
3048 The control unit at address 48 is not working
3049 ART control unit not working
OR
The control unit at 49 is not working
3050-3099 The control unit at addresses from 50 to 99 is not working
3100 EAB control unit out of order
کد های مکمل با ترجمه فارسی را بگذارید و آشنا سازی سیستم هارا