Deciphering diagnostic trouble codes for VECU MID 144 Volvo control units
See also:
MID 144 PID 29
Parameter:
Accelerator pedal sensor number 2 (only for cars with dual controls)
Fault:
FMI 3 The voltage of the signal from the pedal sensor is higher than 4.3 V. A break in the ground wire. Closing the signal wire to a higher voltage. Faulty sensor or idling switch 3 accelerator pedals.
FMI 4 The signal voltage from the pedal sensor is below 0.4 V. Breakage of the signal or supply wire. Shorting the signal wire to ground. The pedal sensor may be faulty.
MID 144 PID 46
Parameter:
Air pressure in the primary receiver (only for cars with air suspension)
Fault:
FMI 0 The pressure in the air suspension receiver is above normal. The compressor discharge valves in the compressor head are faulty, the wiring of the compressor discharge solenoid valve in the dryer is damaged. Damaged, dirty or clogged compressor discharge valve in the drier. The air pressure sensor is faulty (the sensor is located behind the instrument panel on the right).
FMI 1 The vehicle control unit receives a signal from a sensor with a voltage below 3.1 V (corresponds to 9.7 bar) for the older version and below 2.6 V (corresponds to 8.0 bar) for a newer version. Air pressure below normal. Air leaks, clogged, damaged air lines or air suspension components.
FMI 3 The vehicle control unit receives a signal from a sensor with a voltage higher than 4.5 V (corresponding to 15 bar). Broken wire connection to ground. Shorting the signal wire to a higher voltage. Theair pressure sensor may be faulty (the sensor is located behind the instrument panel on the right).
FMI 4 The vehicle control unit receives a signal from a sensor with a voltage above 0.5 V. Breakage of the signal or supply wires. Shorting the signal wire to ground. Air pressure sensor may be faulty.
FMI 14 It appears when the signal from the vehicle control unit is sent to the desiccant, and the air pressure in the system continues to increase. Damaged or blocked tube control valves of the compressor from the desiccant. Faulty valves in the compressor head (jammed in the closed position). Damaged wiring between the vehicle control unit and the discharge valve on the water dryer. Damaged, dirty or clogged compressor discharge valve in the drier. The air pressure sensor is faulty (the sensor is located behind the instrument panel on the right). The safety valve should go off. If the safety valve is clogged and does not work, the compressor head seals may fail and large amounts of air from the compressor may enter the engine cooling system.
MID 144 PID 84
Parameter:
Car speed signal
Fault:
FMI 2 There is a big difference between the speed signals from the tachograph (via the SAE J1939 data channel or to the contact of the vehicle control unit PB6) and the speed signals from the wheel rotation sensors (ABS). Before searching for faults in the vehicle control unit system, read the fault codes of the ABS / EBS systems and eliminate the causes of their occurrence. It is also possible that the wiring is faulty or the signals from the tachograph are not correct. Perhaps there were manipulations with the speed sensor or with the wiring between the speed sensor on the gearbox and the tachograph.
FMI 14 Tachograph speed signals are not correct. Damaged wiring. Perhaps defective speed sensor on the gearbox or tachograph.
MID 144 PID 86
Parameter:
Set speed (cruise control)
Fault:
FMI 14 The vehicle control unit (VECU) does not receive information from the adaptive cruise control unit (ACC) via the SAE J1939 data channel. Breaking or partial damage to the data channel. The ACC unit may be faulty.
MID 144 PID 91
Parameter:
Accelerator pedal position
Fault:
FMI 3 The voltage of the signal coming to the control unit from the accelerator pedal sensor is higher than 4.3 V. Break in the power or ground wire. Shorting the signal wire to a higher voltage. The pedal position sensor or the idle switch No. 1 pedal may be faulty. The sensor and switches are integrated with the accelerator pedal.
FMI 4 The voltage of the signal to the control unit from the accelerator pedal sensor is less than 0.4 V. The break in the power or signal wire. Shorting the signal wire to ground. Defective or oxidized contacts in the connectors. Accelerator pedal position sensor may be faulty.
FMI 5 The low level signal from the position sensor does not match the signals from the idling switch No. 1 or No. 2. The pedal position sensor is faulty. Damaged or oxidized pins in connectors.
FMI 6 The high level signal from the position sensor does not match the signals from the idling switch No. 1 or No. 2. The pedal position sensor is faulty. Damaged or oxidized pins in connectors.
FMI 14 Malfunction in the power circuit. Breakage or partial damage to the power cord.
MID 144 PID 150
Parameter:
Power takeoff
Fault:
FMI 4 The voltage at the PBV contact of the vehicle control unit with an unused function is below 2.3 V. Break in the power supply wire of the power take-off solenoid valve. Broken wire between the valve and the control unit. Damaged or oxidized pins in connectors. The solenoid valve may be faulty.
MID 144 PID 152
Parameter:
The number of reinstalls car control unit
Fault:
FMI 12 The code is registered in the event of an internal software failure, and the internal independent function of restarting the vehicle control unit is triggered. The code is informational and is not a malfunction code.
MID 144 SID 230
Parameter:
Idle switch № 1 accelerator pedal
Fault:
FMI 7 The accelerator pedal is fully released, and the signal from the idle switch does not flow to the vehicle control unit. Break signal or power wires. Shorting the signal wire to ground or positive.Damaged or oxidized pins in connectors. Perhaps a faulty switch integrated with the accelerator pedal.
MID 144 SID 231
Parameter:
SAE J1939 data feed
Fault:
FMI 2 The control unit does not receive messages over the SAE J1939 data channel. Breakage or partial damage to the data channel wiring. Damaged or oxidized pins in connectors.
FMI 12 The control unit does not receive messages over the SAE J1939 data channel. Breakage or partial damage to the data channel wiring. Damaged or oxidized pins in connectors.
MID 144 SID 250
Parameter:
SAE J1708 data feed
Fault:
FMI 2 Errors in messages on the data channel SAE J1708. Partial damage to the data channel wiring.
MID 144 SID 253
Parameter:
Gauge EEPROM Memory
Fault:
FMI 2 Programming error or control unit memory chip is faulty. Try to reprogram the unit (performed only on authorized service stations).
FMI 14 Data error Faulty memory chip in control unit or software error. Try to reprogram the unit (performed only on authorized service stations).
MID 144 PPID 3
Parameter:
Starter relay
Fault:
FMI 3 Very strong current through the power stage. Short to power plus. Faulty wiring or short circuit in the relay coil.
FMI 4 Faulty relay, wire break or short to ground.
MID 144 PPID 61
Parameter:
Retarder switch
Fault:
FMI 7 Faulty wiring or switch.
MID 144 PPID 69
Parameter:
Buffered Idle Switch
Fault:
FMI 3 The signal from the buffered idle switch does not match the signal from the idle switch No. 1 accelerator pedal. Signal wire shorted to ground.
FMI 4 The signal from the buffered idle switch does not match the signal from the idle switch No. 1 accelerator pedal. Signal wire shorted to ground.
MID 144 PPID 70
Parameter:
Power supply for accelerator, brake and clutch pedal switches
Fault:
FMI 4 The vehicle control unit has detected a voltage lower than 3 V on the power wire of the switches. Shorting of the power wire to ground, short circuit of the signal wire of the accelerator pedal switch, brake or clutch to ground.
MID 144 PPID 71
Parameter:
Power to the retarder and cruise control switches
Fault:
FMI 4 The vehicle control unit has detected a voltage lower than 3 V on the power wire of the switches. Shorting of the power wire to ground. Closing the cruise control switch signal wire SET + / SET- / RESUME / ON. A short to ground on the signal wire of the VCB / EPG engine brake switch. A short to ground on the signal wire of the retarder switch SET + / SET-. One of the switches may be faulty.
MID 144 PPID 72
Parameter:
Power supply for accelerator pedal sensor and retarder switch
Fault:
FMI 3 The car control unit has detected a voltage of more than 5.3 V on the power supply wire. A break in the ground wire, a short to a higher voltage, a break in the power wire. The retarder switch or the accelerator pedal sensor may be faulty. Damaged or oxidized pins in connectors.
FMI 4 The vehicle control unit has detected a voltage lower than 4.7 V on the power wire. Shorting of the power wire to ground. The retarder switch or the accelerator pedal sensor may be faulty.
MID 144 PPID 73
Parameter:
Power supply air pressure sensor in the primary receiver (air suspension) and switch “Dynafleet”
Fault:
FMI 3 The vehicle control unit has detected a voltage of more than 5.3 V on the power wire. An open circuit of the ground wire, a short circuit of the power wire to a higher voltage, an open circuit of the power wire. The air pressure sensor may be faulty (located behind the instrument panel on the right) or the “Dynafleet” switch.
FMI 4 The vehicle control unit has detected a voltage lower than 4.7 V on the power wire. Shorting of the power wire to ground. The air pressure sensor may be faulty (located behind the instrument panel on the right) or the “Dynafleet” switch.
MID 144 PPID 74
Parameter:
Power supply to the engine control unit EECU and the vehicle control unit VECU
Fault:
FMI 3 The control voltage of the relay K2 is from the PB15 contact of the vehicle control unit above 1 V. Short circuit to a higher voltage or the relay K2 is faulty (located on the central distribution board of the relay and fuses in the middle of the instrument panel).
FMI 4 The control voltage of the relay K2 from the PB15 contact of the vehicle control unit is below 0 V. There is a wire break with the relay K2 or the relay is faulty.
MID 144 PPID 75
Parameter:
Range Locking
Fault:
FMI 3 The vehicle control unit registers a voltage higher than 6.5 V at the PB18 contact. A short circuit between the solenoid valve of the range dial lock (located at the rear of the gearbox on the range ring cylinder) and the vehicle control unit is connected to the power cord. The solenoid valve may be faulty.
FMI 4 The vehicle control unit registers a voltage below 2.3 V at the PB18 contact. A break in the supply wire of the demultiplicator blocking solenoid valve. A short to ground between the solenoid valve and the control unit. The solenoid valve may be faulty (located at the rear of the transmission on the range-cylinder cylinder). Damaged or oxidized pins in connectors.
MID 144 PPID 76
Parameter:
Brake Relay
Fault:
FMI 3 The vehicle control unit registers a voltage of more than 6.5 V. A short to the power wire or a faulty relay.
MID 144 PPID 79
Parameter:
Range Locking, Solenoid Valve Condition
Fault:
FMI 3 The vehicle control unit has detected a voltage of more than 6.5 V. The short circuit of the wire between the relay K8 and the vehicle control unit. Relay K8 may be faulty (located on the central distribution board of the relay and fuses in the middle of the instrument panel).
FMI 4 The vehicle control unit has detected a voltage of less than 2.3 V. Closing the wire between the relay K8 and the vehicle control unit to ground. Break in the power wire of the relay or wire between the relay and the vehicle control unit. Relay K8 may be faulty (located on the central distribution board of the relay and fuses in the middle of the instrument panel).
MID 144 PPID 145
Parameter:
Block switches road information system “Dynafleet”.
Fault:
FMI 3 The voltages on the power wire of the switch box are above 5 V. The wiring is damaged or the “Dynafleet” switch is faulty.
FMI 4 The voltages on the power supply of the switch box are below 0.5 V. The wiring is damaged or the “Dynafleet” switch is faulty.
MID 144 PPID 265
Parameter:
Power supply vehicle speed sensor on the gearbox
Fault:
FMI 3 The voltage on the power wire between the vehicle control unit and the speed sensor is above 9 V. Break of the ground wire. Shorting the signal wire to a higher voltage. There may be a speed sensor malfunction.
FMI 4 The voltage on the power wire between the vehicle control unit and the speed sensor is below 6.5 V. Breakage of the signal or supply wire. Shorting the signal wire to ground. There may be a speed sensor malfunction.
MID 144 PPID 279
Parameter:
Dehumidifier filter
Fault:
FMI 0 The life of the filter drier, calculated by the control unit of the car, is over.
MID 144 PPID 302
Parameter:
Condition of heating of mirrors
Fault:
FMI 3 A short to a higher voltage or a faulty relay.
FMI 4 Broken wire from relay or faulty relay.
FMI 12 Faulty relay.
MID 144 PPID 312
Parameter:
Regeneration air dryer
Fault:
FMI 0 Very high air flow rate due to air leaks or frequent use of equipment that requires large amounts of compressed air to operate.
FMI 7 The regeneration valve is open for 30 seconds, while the pressure in the pneumatic system has not changed. The dehumidifier muffler is clogged, the regeneration valve is dirty, defective and does not open. Damaged wiring between the control unit and the dehumidifier solenoid valves. Check fuses F10 or F6 (depending on the version of the electronic equipment). Check for the presence of a 24 volt supply on the black wire of the connector of the solenoid valve of the desiccant.
MID 144 PPID 430
Parameter:
Regeneration air dryer
Fault:
FMI 0 Very high air flow rate due to air leaks or frequent use of equipment that requires large amounts of compressed air to operate.
MID 144 PSID 1
Parameter:
Retarder switch
Fault:
FMI 7 The vehicle control unit receives signals from the “SET +” and “SET-” simultaneously. The signal wire is shorted to the power wire or the switch is faulty.
MID 144 PSID 2
Parameter:
Standby idle switch № 2 accelerator pedal (only for cars with automatic gear shifting)
Fault:
FMI 7 When you release the accelerator pedal, the control unit does not receive a signal from the idling switch number 2. Open power or signal wire. Shorting the signal wire to plus or ground. Damaged or oxidized pins in connectors. Perhaps a faulty switch integrated with the accelerator pedal.
MID 144 PSID 3
Parameter:
The switch of idling № 3 (for cars with an additional accelerator, with dual control)
Fault:
FMI 7 The signal in the range of 0-13% of the idle switch does not flow to the vehicle control unit. Open power or signal wire. Shorting the signal wire to plus or ground. Damaged or oxidized pins in connectors. Perhaps a faulty switch integrated with the accelerator pedal.
MID 144 PSID 4
Parameter:
Retarder Switch Lever
Fault:
FMI 3 The vehicle control unit detects a voltage above 4.8 V. A break in the ground wire. Shorting the signal wire to a plus. Damaged or oxidized pins in connectors. Possible defective moderator switch lever.
FMI 4 The vehicle control unit detects a voltage below 0.2 V. An interruption in the supply or signal wire. Closing the signal wire to ground. Damaged or oxidized pins in connectors. Possible defective moderator switch lever.
MID 144 PSID 5
Parameter:
Brake pedal sensor
Fault:
FMI 7 Error in the signal from the brake pedal sensor. Damaged, oxidized contacts or faulty sensor.
MID 144 PSID 7
Parameter:
Speed threshold 2
Fault:
FMI 3 An abnormally high voltage is detected at terminal PB2 of the car control unit. Shorting the signal wire to a plus. Oxidation or high resistance. Faulty relay.
FMI 4 An abnormally low voltage is detected at terminal PB2 of the car control unit. Closing the signal wire to ground. Oxidation or high resistance. Faulty relay.
MID 144 PSID 8
Parameter:
Neutral position
Fault:
FMI 2 The vehicle control unit has detected that the requested gear does not match the actual one. Defective neutral position sensor on the gearbox.
FMI 3 The control unit of the car found that when reaching a speed above 50 km / h, the state of neutral position did not change. Broken wire mass sensor neutral position. Signal wire closure to plus.Oxidation or high resistance.
FMI 4 The control unit of the car found that when reaching a speed above 50 km / h, the state of neutral position did not change. Broken wire signal sensor neutral position. Shorting the signal wire to ground. Oxidation or high resistance.
MID 144 PSID 9
Parameter:
Clutch pedal sensor
Fault:
FMI 3 The control unit of the car found that the position of the clutch pedal does not change when it reaches a speed above 50 km / h. Broken wire mass sensor. Signal wire closure to plus. Damaged, oxidized contacts or faulty sensor.
FMI 4 The control unit of the car found that the position of the clutch pedal does not change when it reaches a speed above 50 km / h. Broken wire signal sensor neutral position. Shorting the signal wire to ground. Oxidation or high resistance.
MID 144 PISD 10
Code
Pisd 10
Parameter:
Relay K41 reversing light
Fault:
FMI 3 An abnormally high voltage is detected at terminal PB4 of the car control unit. Mass wire breakage. Shorting the signal wire to a plus. Oxidation or high resistance.
FMI 4 An abnormally low voltage is detected at the vehicle control unit PA8 terminal. Closing the signal wire to ground. Oxidation or high resistance.
MID 144 PSID 11
Parameter:
Relay K42 braking signals
Fault:
FMI 3 An abnormally high voltage is detected at terminal PB28 of the car control unit. Mass wire breakage. Shorting the signal wire to a plus. Oxidation or high resistance.
FMI 4 An abnormally low voltage is detected on the contact PВ28 of the car control unit. Closing the signal wire to ground. Oxidation or high resistance.
MID 144 PSID 14
Parameter:
Datamax Error
Fault:
FMI 2 General failure. Switch off the ignition for at least 1 minute. If the error is active, reprogram the control unit.
MID 144 PSID 19
Parameter:
Status of the parking brake (relay K15)
Fault:
FMI 3 An abnormally high voltage is detected at terminal PB16 of the car control unit. Mass wire breakage. Shorting the signal wire to a plus. Oxidation or high resistance.
FMI 4 An abnormally low voltage is detected on the PV16 contact of the car control unit. Closing the signal wire to ground. Oxidation or high resistance.
MID 144 PSID 20
Parameter:
Power takeoff signal
Fault:
FMI 3 The vehicle control unit registers at the PB16 contact from the solenoid power take-off valve a high voltage or voltage equal to the battery voltage. Shorting the wire between the solenoid valve and the control unit to a higher voltage, or the solenoid valve is faulty.
FMI 4 The vehicle control unit registers a voltage below 2.3 V at the PB16 contact from the solenoid power take-off valve. An open wire to the solenoid valve or a wire between the solenoid valve and the control unit. Short to ground between the solenoid valve and the control unit. Solenoid valve defective.
MID 144 PSID 21
Parameter:
CAN 1
Fault:
FMI 14 The SAE J1939 data channel of the CAN 1 network transmits messages that are not supported by the control unit in accordance with the vehicle configuration. Change car configuration.
MID 144 PSID 22
Parameter:
CAN 2
Fault:
FMI 14 The SAE J1939 data channel of the CAN 2 network transmits messages that are not supported by the control unit in accordance with the vehicle configuration. Change car configuration.
MID 144 PSID 23
Parameter:
Regeneration air dryer
Fault:
FMI 3 The vehicle control unit registers at the contact PB4 or PB3 a higher voltage or voltage equal to the voltage of the batteries. Signal wire closure to plus. Defective solenoid valve defective.
FMI 4 The vehicle control unit registers a voltage below 2.3 V at the PB4 or PB3 terminal. A break in the signal or supply wire. Shorting the signal wire to ground. Oxidation or high resistance. Defective solenoid valve defective.
MID 144 PSID 24
Parameter:
Air dryer, compressor control
Fault:
FMI 3 The vehicle control unit registers at the contact PB4 or PB1 a higher voltage or voltage equal to the voltage of the batteries. Signal wire closure to plus. Defective solenoid valve defective.
FMI 4 The vehicle control unit registers a voltage below 2.3 V at the PB4 or PB1 terminal. A break in the signal or supply wire. Shorting the signal wire to ground. Oxidation or high resistance. Defective solenoid valve defective.
MID 144 PSID 25
Parameter:
Air leak
Fault:
FMI 1 Air flow rate from the pneumatic system, at a speed of over 50 km / h, is higher than the allowable value. Air leaks in the vehicle or trailer system.
MID 144 PSID 200
Parameter:
Communication failure over SAE J1939 data link with MID128 engine control unit
Fault:
FMI 9 The vehicle control unit MID144 for 5 seconds does not receive signals via data channel SAE J1939 from the engine control unit MID128. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 202
Parameter:
Communication failure over SAE J1939 data link with dashboard control unit MID140
Fault:
FMI 9 MID144 does not receive a date and time message from the MID140 dashboard unit. Data link is broken or one of the control units is faulty.
MID 144 PSID 204
Parameter:
Communication failure over SAE J1939 data link with MID136 braking system control unit
Fault:
FMI 9 The vehicle control unit MID144 for 5 seconds does not receive signals via data channel SAE J1939 from the control unit of the braking system MID136. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 205
Parameter:
Communication failure over SAE J1939 datapath with MID130 transmission control unit
Fault:
FMI 9 The control unit MID144 for 5 seconds does not receive signals via data channel SAE J1939 from the control unit of the gearbox MID130. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 206
Parameter:
Communication failure over SAE J1939 data link with the retarder control unit MID222
Fault:
FMI 9 The vehicle control unit MID144 for 5 seconds does not receive signals via data channel SAE J1939 from the control unit of the retarder MID222. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 207
Parameter:
Communication failure over SAE J1939 data channel with MID223 gear selector control unit
Fault:
FMI 9 The vehicle control unit MID144 for 5 seconds does not receive signals via data channel SAE J1939 from the control unit selector gear MID223. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 208
Parameter:
Communication failure over SAE J1939 data channel with MID150 air suspension control unit
Fault:
FMI 9 The vehicle control unit (MID144) does not receive the vehicle weight message via the SAE J1939 data channel from the air suspension control unit MID150 for 5 seconds. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 210
Parameter:
Communication failure over SAE J1939 data channel with MID216 outdoor lighting control unit
Fault:
FMI 9 Driving unit MID144 within 5 seconds does not receive the channel SAE J1939 data from external lighting control unit MID216. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 211
Parameter:
Communication failure over SAE J1939 data channel with MID219 adaptive cruise control unit
Fault:
FMI 9 Driving unit MID144 within 5 seconds receives no communication channel SAE J1939 data from the control unit adaptive cruise control MID219. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 212
Parameter:
Communication failure over SAE J1939 data channel with tachograph control unit MID220
Fault:
FMI 2, 9, 14 The control unit MID144 for 5 seconds does not receive messages via the data channel SAE J1939 from the control unit tachograph MID220. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 214
Parameter:
Communication failure over SAE J1939 data channel with MID249 option control unit
Fault:
FMI 9 Driving unit MID144 within 5 seconds does not receive the channel SAE J1939 data from additional equipment MID249 control unit. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 227
Parameter:
Communication failure over SAE J1939 data channel with MID185 air dryer control unit
Fault:
FMI 9 The control unit of the car MID144 within 5 seconds does not receive messages via the data channel SAE J1939 from the control unit of the air dryer MID185. Breakage or partial damage to the data channel wires. between the blocks.
MID 144 PSID 230
Parameter:
Software failure
Fault:
FMI 4 Incorrect software restart. Power outages, software malfunctions, or strong electromagnetic interference.
FMI 5 Incorrect interruption of the program due to a power failure. There was no power for at least 10 seconds when the ignition is on. Breakage or partial damage to the power cord or ground of the vehicle control unit .
FMI 12 Serious software malfunction and software restarted. Software error or strong electromagnetic interference. Reprogram the vehicle control unit first, if the fault persists, replace the vehicle control unit.
MID 144 PSID 232
Parameter:
SAE J1939-2 data feed
Fault:
FMI 2 The vehicle control unit does not communicate with the tachograph control unit via data channel SAE J1939. Breakage of wires between the car control unit and the tachograph. A short to ground between the car control unit and the tachograph.
I have a 2019 mack roll off truck i cant find a psid code higher than 232 and i have a fault code MID 144 PSID 247 FMI 14. How do i look this up??
This is worthless, my code is not displayed